Multitech ISI4608 Especificaciones

Model Number ISI4608Quick Start Guide

10ISI4608 Quick Start GuideSafety Warnings Telecom1. Never install telephone wiring during a lightning storm.2. Never install telephone jacks in wet l

11Chapter 2 - InstallationWhen selecting a unique base I/O address, be sure that the nextaddress is also unused. To determine your ISI's current

12ISI4608 Quick Start GuideHardware Installation ProcedurePerform the procedures in Table 2-2 to install the ISI4608 card(s) inyour PC-ISA bus compute

13Chapter 2 - InstallationTable 2-2 (cont’d)Step Procedure4a The default setting for the ISI4608’s base I/O address is 210hex. The default value for t

14ISI4608 Quick Start GuideTable 2-2 (cont’d)Step ProcedureFigure 2-2. Octopus Cable8 Turn power on to the computer and refer to the manual thatwas p

Chapter 3 - Driver Installation

16ISI4608 Quick Start GuideIntroductionThis chapter describes software/driver installation for the ISI cardswhen used in Windows 2000, Windows NT4, Wi

17Chapter 3 - Driver Installation The I/O Address DIP Switch and the IRQ Jumper Block are at thetop middle of the ISI4608 circuit board and on

18ISI4608 Quick Start GuideSelect the value that matches the Base I/O Address value that youhave already set on the ISI4608 board in Step 2. Click OK

19Chapter 3 - Driver Installationversion of Windows 2000. (The ISI Management Software can beinstalled only in the Windows 2000 Server and Windows 200

Quick Start GuideP/N 82081106, Revision BModel #ISI4608This publication may not be reproduced, in whole or in part, without priorexpressed written per

20ISI4608 Quick Start GuideISI4608 Software Installation Procedure forWindows NT 3.51/4.01. Turn off the PC.2. The ISI4608 card must be installed in a

21Chapter 3 - Driver Installation8. The Select OEM Option dialog box appears. Click OK.A transient dialog box will appear indicating the progress of

22ISI4608 Quick Start GuideISI4608 Software Installation Procedurefor Windows 95/98/ME1. Turn off the PC.2. The ISI4608 card must be installed in an I

23Chapter 3 - Driver Installation6. Launch the setup program. (From Windows Explorer, double-click onsetup.exe; from the Run menu, click OK.)7. The i

24ISI4608 Quick Start GuideRemoving the ISI4608 Driver (Windows 95/98/Me)1. Click Settings, Control Panel, and then double-click Add/RemovePrograms.2.

25Chapter 3 - Driver InstallationIf you have downloaded the ISI driver from the MultiTech web siteonto a diskette, use this command:COPY A:\NOVELL\AIO

26ISI4608 Quick Start Guide*Error: ISI4608 got out of sync**Error: ISI4608 verify failed at address X**Error: Expected X received Y**Error: Verify got

27Chapter 3 - Driver InstallationTo format a floppy disk for SCO5:1. At the Unix prompt, run the scosh program.2. Select Manager.3. Select Archive.4.

28ISI4608 Quick Start Guide5. To verify that the files have been copied onto the floppy disk, usethese commands:# scosh - Select Manager. - Select Arc

29Chapter 3 - Driver Installation11. Type Y (yes) to accept the prefix for tty ports. For further detailssee MultiTech Installation Script step 3.12

ContentsChapter 1 - Introduction and Description ...5Introduction to the IntelligentSerialInterface ...6

30ISI4608 Quick Start Guideto be created in your /dev directory. Thesedevices are system-wide resources.Enter the number of pseudo-devices to becreat

31Chapter 3 - Driver Installationselect will be used for all ports on each card you install. ISI portdesignations will have this form:[basename prefix

32ISI4608 Quick Start Guiderebuilt. After the terminals have been added to the Terminal Controldatabase, and when the display says Press <Ente

33Chapter 3 - Driver InstallationACU ttylbX - 9600 dialer name. Replace b, X anddialer-name with appropriate values.3. Repeat this process for each

34ISI4608 Quick Start GuideLinux Driver for Multi-Tech ISI Server CardsLINUX: Pre-Installation IssuesWhen unpacking the Linux driver, there are two ch

35Chapter 3 - Driver InstallationLINUX: Copying and untarring the driver from afloppyThe ISI driver .tar file can be copied from a DOS formatted flopp

36ISI4608 Quick Start GuideIRQ to be used. The installation creates the script file 'ISICOMStart' inthe destination folder. 'ISICOMSt

37Chapter 3 - Driver InstallationLINUX: Verifying the portsTerminal utilities like 'minicom' can be used to verify the ports,'talk&apos

38ISI4608 Quick Start GuideDevices mapped for ISI4608 cards):For the ISI4608 card (8 ports):- /dev/ttyM1a to /dev/ttyM1h should be mapped for modem po

39Chapter 3 - Driver InstallationNormal ports (ttyM) are configured for dial-in connections. Callout ports(cum) are used for dial-out connections.To

LINUX: Driver installation and loading... 35LINUX: Setting the baud rate ...

40ISI4608 Quick Start Guide

Chap 4: Warranty, Service & Tech Support

42ISI4608 Quick Start GuideWarranty, Service & Tech SupportLimited WarrantyMulti-Tech Systems, Inc., (hereafter “MTS”) warrants that its productsw

43Chapter 4 - Warranty, Service and Tech SupportAgreement for details on rates and coverages.Please direct your questions regarding technical matters,

44ISI4608 Quick Start Guidevia the MultiTech web site and/or the MultiTech FTP site.www.multitech.com. Go to Support page. Drivers, software, andfir

45Chapter 4 - Warranty, Service and Tech Supportas Licensee. The License includes the distribution diskette or CD-ROM, other accompanying programs, an

46ISI4608 Quick Start Guidethis agreement.Licensee agrees that any breach of this agreement will be damagingto Multi-Tech Systems, Inc.Licensee agrees

Index

48ISI4608 Quick Start GuideIndexAactivating ports in SCO 33CCabling 8Computer Requirements 8configurationportsin Netware 25DDB78S female connector 13D

49IndexLLinux, install in 34Mmodemsactivating portsSCO 32OOctopus Cable 14on-line warranty registration 46Pport activationSCO 32port allocationLinux 3

Chapter 1 - Introduction and Description

82081106

6ISI4608 Quick Start GuideIntroduction to the IntelligentSerialInterfaceThe new IntelligentSerialInterface card, model ISI4608, is ahardware solution

7Chapter 1 - Introduction and DescriptionProduct DescriptionThe ISI4608 is a multiport serial port expansion card which adds databuffering on each por

8ISI4608 Quick Start GuideTechnical SpecificationsComputer Requirements• 386, 486, or Pentium®- based PC or compatible with ISA BusArchitecture• Micro

Chapter 2 - Hardware Installation