Multitech Zpx Multimodem MT5634ZPX-PCI-V92 Guía de usuario descargar pdf (Pagina 34)

D Installing Under Linux

MultiModemZPX User Guide

Note: The preceding example places the modem on COM3. Your IRQ and port

may vary. Substitute the IRQ and port values in the example with the values for

your computer as listed in the results of the command issued in step 3. To set

Linux to configure the modem at boot-up, use an editor such as “jed” and add the

setserial command to the end of the rc.local file.

5. Once you’ve completed your installation, you must configure your modem for country-

specific operation. See Chapter 2 for information on using AT commands to configure your

modem for use in your country.

Using the Terminal Program Minicom to Verify Operation

This section describes how to make sure Linux can talk to the modem and be able to dial up to the

Internet. Linux can use different programs and desktops depending on who made the Linux operating

system and what version it is. The following procedures use the most commonly installed components

of Red Hat 6.2. More information can be found in your Linux OS owner’s manual.

1. At the command prompt, type minicom –s and press E

NTER.

2. Select Serial port setup and press ENTER.

3. From Serial port setup, use the A key to access Serial Device, and then press ENTER.

4. Press ESC.

5. You are now in the Minicom terminal. Type AT and press ENTER. The screen should display

OK to verify the operation. Alternately, dial a phone number to verify line operation

6. To leave Minicom, press CTRL + A, and then press Z.

7. On the help menu, press X to exit.

Using the Modem to Call the Internet

Linux allows different graphic user interfaces (GUI). In the following steps, we’ll use the Gnome

Desktop GUI and assume that the Internet Service Provider (ISP) you are calling assigns you the

Domain Name Service (DNS) and Internet Protocol (IP) addresses. For more information on DNS or IP,

see the Linux OS owner’s manual or contact your ISP.

1. On the Task Bar at the bottom of the screen, select the Gnome Footprint.

2. Select Internet from the menu.

3. Select Dialup Configuration Tool.

4. Select Add, and then click Next.

5. Enter the connection name and phone number, and then click Next.

6. Enter your user name and password, and then click Next.

7. Select Normal ISP if your ISP is not listed, and then click Next.

8. Click Finish.

1 2 ... 29 30 31 32 33 34 35 36 37

Comentarios a estos manuales

Sin comentarios

Models	Document Type
DTS 3181 SL–115V / 230V	User Manual Pfannenberg DTS 3181 SL–115V / 230V User Manual, 3 pages
DTx 9021 115V 60Hz	User Manual Pfannenberg DTx 9021 115V 60Hz User Manual, 4 pages
DTx 9021 230V 50/60Hz	User Manual Pfannenberg DTx 9021 230V 50/60Hz User Manual, 4 pages
DTFI 9021	User Manual Pfannenberg DTFI 9021 User Manual, 52 pages
PWS Series	User Manual Pfannenberg PWS Series User Manual, 16 pages
PAI	User Manual Pfannenberg PAI User Manual, 46 pages
DTI 6x01	User Manual Pfannenberg DTI 6x01 User Manual, 60 pages

Multitech Zpx Multimodem MT5634ZPX-PCI-V92 Guía de usuario Pagina 34

Comentarios a estos manuales

Pfannenberg DTS 3181–400V / 460V manuals

Pfannenberg DTS 3181–400V / 460V User Manual (3 pages)

Table of contents

More products and manuals for Conditioners Pfannenberg

Multitech Zpx Multimodem MT5634ZPX-PCI-V92 Guía de usuario Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Módems Multitech Zpx Multimodem MT5634ZPX-PCI-V92

Pfannenberg DTS 3181–400V / 460V manuals

Pfannenberg DTS 3181–400V / 460V User Manual (3 pages)

Table of contents

More products and manuals for Conditioners Pfannenberg