Multitech MTCBA-C-U Especificaciones Pagina 58
- Pagina / 197
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 10 – V24-V25 Commands
Multi-Tech Systems, Inc. CDMA AT Commands Reference Guide (PN S000294K) 58
Chapter 10 – V.24-V.25
Commands
Refer to ITU-T Recommendation V.25 specifications if you desire more details about the following commands.
Fixed DTE Rate +IPR
Description: This command is used to specify the baud rate for the module DATA port. The factory default value is
115200. When autobaud is specified (AT+IPR=0), the module sets the DATA port operating baud rate to the
detected DTE baud rate. The AT&F command restores the baud rate value that was active when the last
AT&W command was used.
Note: The use of baud rates below 9600 may affect the operability of some module software features; e.g.,
TCP App.
Syntax: Command syntax: AT+IPR
Command Possible Responses
AT+IPR?
Note: Read syntax.
+IPR: 9600
OK
Note: Current rate is 9600 bps
AT+IPR=?
Note: List of supported <rate> values,[(list of
fixed-only <rate> values)]
+IPR: (0,1200,2400,4800,9600,19200), (45,50,75,
110,150,300,600,38400,57600,115200,230400)
OK Note: Possible value (
*)
AT+IPR=38400
Note: Disable autobaud and set rate to 38400 bps
OK
AT+IPR=0 Note: Enable autobaud OK
(*) The first list of values are the baud rates that are detectable by the module autobaud feature. The second
list of values are the module DATA port supported baud rates
.
DTE-DCE Character Framing +ICF
Description: This command is used to specify the UART start-stop (asynchronous) character framing for the module
DATA port. The factory default value is 3,3. The AT&F command restores the value that was active when
the last AT&W command was used.
Values: <format>
0 Autodetect (Not supported)
1 8 Data 2 Stop (Not supported)
2 8 Data 1 Parity 1 Stop (Not supported)
3 8 Data 1 Stop (Supported)
4 7 Data 2 Stop (Not Supported)
5 7 Data 1 Parity 1 Stop (Not Supported)
6 7 Data 1 Stop (Not Supported)
<parity>
0 Odd (Supported)
1 Even (Supported)
2 Mark (Supported)
3 None (Supported)
Note: The supported format values are software release specific. Use the +ICF=? command to display the valid
format values for the software release in use.
Syntax: Command syntax: AT+ICF= <format>, <parity>
Command Possible Responses
AT+ICF=3,3
Note: Set values.
OK
Note: New values set
AT+ICF?
Note: Display current settings.
+ICF: 3,3
OK
Note: Current values
AT+ICF=?
Note: Display valid parameter ranges.
+ICF: (3-5),(0-3)
OK
Note: Possible values
- CDMA AT Commands 1
- Contents 3
- Chapter 1 – Introduction 9
- Terminology and Acronyms 10
- Chapter 2 – AT Command 13
- Features 13
- Attention AT 14
- Request IMSI +CIMI 15
- Capabilities List +GCAP 15
- Repeat Last Command A/ 15
- Phone Offline +CPOF 16
- Keypad Control +CKPD 17
- Clock Management +CCLK 17
- Ring Melody Playback +CRMP 17
- Ringer Sound Level +CRSL 18
- Subscriber Number +CNUM 18
- View Modem Timers +WTMR 19
- Chapter 4 – Call Control 20
- Hang-Up Command H 21
- Answer a Call A 22
- Remote Disconnection 22
- DTMF Signals +VTD, +VTS 23
- Automatic Answer S0 24
- Incoming Call Bearer +CICB 25
- Microphone Gain +VGT 26
- Volume Gain Control +VGR 26
- Echo Cancellation +ECHO 27
- TTY Mode +WTTY 28
- Chapter 5 – Network Service 29
- Band Preference +WBND 30
- Roam Preference +WRMP 31
- Change NAM Selection +WNAM 32
- Read Current NAM +WCNM 32
- Chapter 6 – SIM Card 35
- Operational Commands 35
- Enter PIN2 +CPIN2 36
- Change Password +CPWD 38
- Card Identification +CCID 38
- Chapter 7 – Short Messages 39
- Delete Message +CMGD 47
- Message Overwriting +WMGO 49
- Change SMS Status +WUSS 49
- Chapter 8 – Supplementary 51
- Services Commands 51
- Chapter 9 – Data Commands 55
- Cellular Result Codes +CRC 56
- Chapter 10 – V.24-V.25 58
- Set DCD Signal &C 59
- Set DTR Signal &D 60
- Set DSR Signal &S 60
- Back to Online Mode O 60
- Result Code Suppression Q 60
- DCE Response Format V 61
- Audio Loopback &T 61
- Echo E 61
- Save Configuration &W 62
- Chapter 11 – Phone Book 63
- Phonebook Read +CPBR 66
- Phonebook Search +CPBP 66
- Chapter 12 – Position 68
- Determination (GPS) 68
- IP Server Address +WMPC 73
- Chapter 13 - Specific AT 74
- Read GPIO Value +WIOR 78
- Write GPIO Value +WIOW 78
- Play Tone +WTONE 78
- Play DTMF Tone +WDTMF 79
- Hardware Version +WHWV 79
- Select Voice Gain +WSVG 80
- Status Request +WSTR 80
- Ring Indicator Mode +WRIM 81
- 32kHz Sleep Mode +W32K 81
- Software Version +WSSW 82
- CPHS Command +CPHS 83
- Reset +WRST 84
- Set Standard Tone +WSST 85
- Security PIN +WPIN 86
- Minute Alert +WMBP 87
- Chapter 14 - SIM ToolKit for 89
- RUIM Software Version 89
- Example: 91
- Chapter 15 – Provisioning AT 99
- Set IMSI +WIMI 100
- SID and NID +WSID 101
- Slot Cycle Index +WSCI 101
- Packet Dial String +WPDS 102
- Commit Changes +WCMT 104
- Read SID/NID Entries +WSNR 104
- Download PRL +DPRL 105
- Service Programming Example 106
- Chapter 16 – Extended AT 107
- Commands in IS707.3 107
- Select Pulse Dialing P 108
- Basic S-Registers S 108
- Error Control Report +ER 109
- Modulation Selection +MS 113
- V.18 Selection +MV18S 114
- Cellular Extension +CXT 115
- Configuration String +CFG 115
- Query Service +CAD 115
- Battery Charge +CBC 117
- Serving System +CSS 118
- Hang-up Voice +CHV 119
- Chapter 17 – Qualcomm 121
- Defined AT Commands for 121
- CDMA Operation 121
- Set DM Baud Rate $QCDMR 125
- SCRM’ing Selection $QCSCRM 126
- R-SCH IP Selection $QCMIP 127
- MIP Selection $QCMIPP 128
- Chapter 18 – TCP/IP App AT 133
- Commands 133
- Open Socket +WOSK 134
- Close Socket +WCSK 135
- Transmit Socket Data +WSTX 135
- Read Receive Data +WSRX 136
- Force Dormant Mode +WFDM 138
- IP Address Lookup +WDNS 139
- Display IP Address +WIPC 139
- PPP Session Status +WPPP 139
- Socket State Change +WSKS 140
- Received Socket Data +WSRX 141
- Socket Data Error +WSRE 141
- Chapter 19 – Reference 143
- Information 143
- Specific Error Result Codes 144
- Final Result Codes 145
- Intermediate Result Codes 145
- Parameters Storage 147
- TCP App Socket Status Events 150
- TCP App Socket Error Codes 150
- TCP App DNS Server Codes 150
- TCP App PPP Network Codes 150
- Phonebook UCS2 Unicode 152
- MuxLite Example 154
- Chapter 20 – Unsolicited AT 155
- Result Codes 155
- Key Press or Release +CKEV 156
- Mode Preference +COPS 158
- Incoming Call +CRING 158
- RxLev Indication +CSQ 159
- Incoming Call +RING 159
- Call Answered +WANS 159
- Call Connected +WCNT 160
- Call Ended +WEND 160
- Flash Indication +WFSH 161
- General Indicator +WIND 161
- Call Originated +WORG 162
- Roaming Indication +WROM 162
- Emergency Mode +WSOS 163
- Current NAM Change +WNAM 163
- Voice Mail Indicator +WVMI 164
- Power Save +WSPS 164
- Download PRL Status +DPRL 167
- Chapter 21 – AT Command 168
- Examples 168
- Incoming Voice Call 169
- Call Waiting 169
- Originate Data Call 169
- Originate Data Call Failure 169
- Short Message Examples 170
- GpsOne Examples 171
- AT Commands 175
- Read Message +CMGR 177
- List Message +CMGL 178
- Send Message +CMGS 179
- Facility Lock +CLCK 185
- Signal Quality +CSQ 185
- Boot URL +WBURL 187
- Trusted Domain +WTDMN 187
- Proxy Address +WDPXY 187
- IOTA Error +WOAE 188
- Please Retry +WOAR 188
- Display PRI Checksum +WSUM 189
Relacionado con productos y manuales para Redes Multitech MTCBA-C-U
Redes Multitech FaxFinder FF840 Manual de usuario
(29 paginas)
(29 paginas)
Redes Multitech MT5634ZBA-USB Guía de usuario
(12 paginas)
(12 paginas)
Redes Multitech ZDX Series Guía de usuario
(10 paginas)
(10 paginas)
Redes Multitech FaxFinder FF840 Especificaciones
(116 paginas)
(116 paginas)
Redes Multitech MultiVOIP 400 MVP400 Guía de usuario
(48 paginas)
(48 paginas)
Redes Multitech CF220 Guía de usuario
(12 paginas)
(12 paginas)
Redes Multitech MTCBA-G-UF1 Especificaciones
(40 paginas)
(40 paginas)
Redes Multitech MT5600SMI Manual de usuario
(4 paginas)
(4 paginas)
Redes Multitech RouteFinder RF850 Guía de usuario
(32 paginas)
(32 paginas)
Redes Multitech MT5600ZDXV Manual de usuario
(58 paginas)
(58 paginas)
Redes Multitech MT5634ZBAV Guía de usuario
(47 paginas)
(47 paginas)
Redes Multitech FR2201 Guía de usuario
(28 paginas)
(28 paginas)
Redes Multitech MultiVOIP 100 MVP120 Guía de usuario
(48 paginas)
(48 paginas)
Redes Multitech RF802EW Guía de usuario
(28 paginas)
(28 paginas)
Redes Multitech MA220 Guía de usuario
(80 paginas)
(80 paginas)
Redes Multitech MA100-1M Guía de usuario
(71 paginas)
(71 paginas)
Redes Multitech FF200 Guía de usuario
(169 paginas)
(169 paginas)
Sylvania 7" Dual Screen Portable DVD SDVD8727 manuales
Manuales del propietario y guías del usuario para Reproductores de dvd Sylvania 7" Dual Screen Portable DVD SDVD8727.
Ofrecemos manuales en pdf Sylvania 7" Dual Screen Portable DVD SDVD8727 para descargar gratis por tipos de documentos:
Más productos y manuales para Reproductores de dvd Sylvania
| Modelos | Tipo de documento |
|---|---|
| Ninguno |
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales