Multitech MTA128ST-USB Manual de instalación Pagina 83
- Pagina / 208
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Connecting power supply
If not using a PoE switch or the 8082 Power Over Ethernet Injector Kit, connect the AC/DC
external adapter:
1. Plug the appropriate cable from the adapter into the set's power supply connector.
2. Connect the plug from the adapter to the mains power supply.
Initializing the sets
The following paragraphs describe how to:
- Select the initialization type
- Initialize the 8082 My IC Phone set
Selecting the initialization type
The default initialization is dynamic.
To select the initialization type, refer to the following table.
table 4.16: Initialization type selection
If Then the required
initialization type is
Further information
You have a DHCP
server
Dynamic or Proprietary
dynamic
- Refer to Configuring the DHCP server
for dynamic initialization
- In case of Proprietary dynamic
selection, the IP address of the set must
be provided by the Proprietary router.
You do not have a
DHCP server
Static - Refer to Configuring network parameters
for static initialization
- Obtain from your network administrator:
• An IP address for the 8082 My IC
Phone set
• The subnetwork mask
• The router address
• The DNS addresses (primary and
secondary)
• The VLAN ID (if VLAN is used)
• The URL of the Alcatel-Lucent
OmniPCX Office Communication
Server for set configuration file
download
Note:
You need to know the set directory number.
Configuring the DHCP server for dynamic initialization
Two types of dynamic initialization are available:
- Dynamic (default value): the set selects in priority DHCP offers, with a Vendor Specific
option corresponding to an Alcatel-Lucent server.
- Dynamic Alcatel: the set accepts only DHCP offers with a Vendor Specific option
&'(
4-37
- Installation Manual 1
- 3
- Chapter 3 4
- Chapter 4 5
- Chapter 5 6
- Chapter 6 6
- Chapter 7 7
- Chapter 8 7
- 9
- 10
- 15
- 15
- 2.3 Installation 19
- 2.4 Equipment 20
- 2.4.2 Detailed description 21
- 2.4.2.2 SLI-X Boards 22
- 2.4.2.3 UAI-X Boards 22
- 2.4.2.4 MIX x/y/z 23
- 2.4.2.5 AMIX-1 X/Y/Z Boards 23
- 2.4.2.6 BRA-X Board 24
- 2.4.2.7 PRA Boards 24
- 2.4.2.9 LAN-X Boards 25
- 2.4.2.8 APA Boards 25
- 2.4.2.10 LANX-2 Boards 26
- 2.4.2.11 DDI-X Board 27
- 2.4.2.12 ATA Board 27
- 31
- # %$ 32
- 3.3 Detailed description 33
- 3.4 Descriptions 39
- 47
- 4.1.1.2.1 Recommendations 48
- 4.2 Connections and Cabling 49
- 4.2.1.1.1 PowerCPU Board 50
- 4.2.1.1.2 SLI Board 50
- 4.2.1.1.9 APA Board 52
- 4.2.1.1.10 DDI Board 52
- 4.2.1.1.11 ATA Board 52
- 4.2.1.2 Types of Cable to Use 52
- 4.2.1.4 Connecting Terminals 53
- Without TL Forwarding 58
- With LR Forwarding 58
- 4.2.1.6 Lan Connection 59
- Audio Input Characteristics: 61
- Fuse Characteristics: 61
- 4.2.1.7.3 Connecting an Alarm 62
- Audio Output Characteristics: 62
- Connecting a NPTT Doorphone 63
- 4.3 Power Supply 65
- External Batteries 66
- 4.3.1.3.2 Hardware 66
- Large Platforms 67
- Platform 74
- 4.3.1.4 Connecting a UPS 77
- Permanent Ground 78
- 4.3.1.6 Power Up 79
- 4.4 SIP Terminals 80
- ___change-end___ 81
- Headsets 85
- External station speakers 85
- 4.4.2.1 Commissioning 86
- 4.4.2.1.1 Overview 86
- Configuring the user by OMC 88
- Connecting the set to the LAN 89
- Connecting the Set 93
- 4.5 8 Series Sets 94
- Prerequisites 100
- Connecting the sets 100
- Connecting power supply 101
- Initializing the sets 101
- Initializing the IP Touch set 102
- Restarting initialization 103
- Connecting optional equipment 103
- Programming keys 105
- Programming a key 105
- 4.6 9 Series Sets 106
- 4.6.2 4029/4039 Digital Phone 108
- 4.6.2.1 Commissioning 108
- 4.6.2.1.1 Overview 108
- 4.7 V24/CTI Interface Module 111
- 4.7.1 Hardware description 112
- 4.7.1.1 Overview 112
- 4.7.1.2 Compliant Standards 112
- 4.7.1.2.1 Safety Requirements 112
- 4.7.2.2 Jumpers 114
- 4.7.3 External connections 114
- 4.8 AP Interface Module 116
- 4.8.1.1 Overview 117
- 4.8.1.2 Compliant Standards 117
- 4.8.1.2.1 Safety Requirements 117
- 4.8.1.2.2 ECM 117
- 4.8.1.2.3 Analog Transmission 117
- 4.8.1.2.4 Environment Classes 118
- 4.8.1.2.5 Eco Design 118
- 4.8.2 Hardware configuration 118
- 4.8.2.1 Overview 118
- 4.8.2.2 Jumper 119
- 4.8.3 External connections 119
- 4.8.3.2 Rear Panel Details 120
- 4.9 S0 Interface Module 121
- 4.9.1.2 Compliant Standards 122
- 4.9.1.2.1 Safety Requirements 122
- 4.9.1.2.2 ECM 122
- 4.9.1.2.3 ISDN 123
- 4.9.1.2.4 Environment Classes 123
- 4.9.1.2.5 Eco Design 123
- 4.9.2 Hardware configuration 123
- 4.9.2.1 Overview 123
- 4.9.2.2 Jumper 124
- 4.9.3 External connections 124
- 4.9.3.3 Power Supply Details 127
- 4.9.3.4 Environment 127
- 4.10.1 Detailed description 127
- 4.10.1.1 CONNECTION 127
- 4.10.1.5 INTERACTIONS 129
- 4.10.1.6 LIMITS 130
- 4.10.1.8 IBS CONFIGURATION 130
- 4.10.1.9 Initialization 132
- Value sent to IBS: 0x3FF 133
- 0000 0011 1111 1111 133
- Value sent to IBS: 0x03FC 135
- 0000 0011 1111 1100 135
- 4.11 PIMphony 138
- 4.11.2 Additional Information 139
- 4.11.2.1 Hardware aspects 139
- 4.11.2.2 Software aspects 139
- 4.12 Reflexes Terminals 140
- 4.12.1.2.3 Wall mounted 141
- Mounting the terminal 141
- 4.13.1 Detailed description 145
- Temporary substitution 145
- Permanent replacement 145
- Replacement of digital sets 146
- 4.13.1.1.3 Moving a handset 147
- 4.13.1.1.4 Adding sets 147
- Interface classification 148
- Server and sets 148
- 4.13.1.4.2 PowerMEX board 150
- 4.13.1.4.3 Role of the # key 151
- 4.13.1.5 Installation Upgrade 151
- 4.13.1.5.2 Migration 152
- Configuration 153
- 5.1 Detailed description 155
- 5.1.1.4 Other predefined data 167
- ! 169
- * 170
- 6.2 System Startup from OMC 177
- " 193
- $ %$ 194
- 199
- 200
© 2020, manymanuals.es. Todos los derechos reservados | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales