Multitech MT9234ZBAUSBCDC Guía de usuario Pagina 29
- Pagina / 66
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 1 – AT Commands, S-Registers, and Result Codes
Multi-Tech Systems, Inc. AT Commands for the MultiModem & SocketModem MT9234 Series (S000434H) 29
+GMR Revision Request
Description: Displays the version of the modem code.
Syntax: AT+GMR? or AT+GMR=?
Reports: +GMR? Reports current or selected options.
+GMR=? Reports supported options.
Result Code: OK
+IFC DTE-DCE Local Flow Control
Description: Use this command to select the local flow control method. The input parameters of
the +IFC command overwrite the settings of the \Q and \X<value> commands. The
reverse is also true. By modifying the settings of the \Q and \X<value> commands,
the +IFC command parameters are overwritten.
Syntax: AT+IFC=<DCE_by_DTE>,<DTE_by_DCE>
Values: +IFC=0,0 No flow control.
+IFC=1,1 Software flow control.
+IFC=2,2 Hardware flow control. (Default)
Reports: +IFC? Reports current or selected options.
+IFC=? Reports supported options.
Result Codes: OK
ERROR
+ILRR DTE-DCE Local Rate Reporting
Description: Use this command to display or hide the local rate report result code. If the rate
report is enabled, the reported <rate> is the current DTE-DCE rate. The rate report is
transmitted after any modulation, error control, or data compression reports, and
before the final result code (e.g., CONNECT).
Syntax: AT+ILRR=<value>
Values: 0 Disables the local rate report. (Default)
1 Enables the local rate report.
Reports: +ILRR? Reports current or selected options.
+ILRR=? Reports supported options.
Result Codes: OK
ERROR
+IPR Fixed DTE Rate
Description: Use this command to set the DTE to DCE transmission rate. There are twelve fixed
transmission rates used by the DTE to communicate with the DCE. These commands
select one of the predefined transmission rates. If a rate is entered which is not
supported, the transmission rate defaults to the next lower rate.
Syntax: AT+IPR=<DTE rate>
Values: +IPR=0 Automatic rate detection. (Default)
+IPR=110 100 bits/s
+IPR=300 300 bits/s
+IPR=600 600 bits/s
+IPR=1200 1200bits/s
+IPR=2400 2400 bits/s
+IPR=4800 4800 bits/s
+IPR=9600 9600 bits/s
+IPR=14400 14400 bits/s
+IPR=19200 19200 bits/s
+IPR=38400 38400 bits/s
+IPR=57600 57600 bits/s
+IPR=115200 115200 bits/s
- Contents 3
- Chapter 1 – AT Commands, S 6
- Registers, and Result Codes 6
- Data and General Commands 7
- E Echo Command 9
- H Hook Control 9
- I Request ID Information 10
- M Monitor Speaker Mode 10
- N Modulation Handshake 11
- Sr S-Register Control 12
- T Select Tone Dialing 12
- V Result Code Format 12
- W Result Code Options 12
- &S Data Set Ready (DSR) 16
- &T Self-Test Commands 16
- \B Transmit Break 18
- \K Break Control 18
- \T Inactivity Timer 19
- \V Protocol Result Code 19
- \X XON/XOFF Pass-Through 20
- -C Data Calling Tone 20
- %C Data Compression Control 21
- %DC AT Command Control 21
- %S Command Speed Response 22
- +DS44 V.44 Data Compression 25
- +ER Error Control Report 26
- +ES Error Control Selection 27
- +GMR Revision Request 29
- +IPR Fixed DTE Rate 29
- +MS Modulation Selection 30
- $D DTR Dialing 32
- $FC Quick Connect 32
- $LB Long Break 32
- $MB Online BPS Speed 33
- $SB Serial Port Baud Rate 33
- +VDR Distinctive Ring Report 34
- #P Set 11-bit Parity 34
- #S Enter Setup Password 34
- #S= Store Setup Password 34
- +VCID Caller ID Selection 35
- Callback Security Commands 36
- #CBP Callback Parity 37
- #CBS Callback Enable/Disable 37
- S-Registers 38
- Result Codes 41
- Chapter 4 – Voice Commands 43
- Voice S-Register Summary 44
- Voice Commands 44
- Support 44
- Voice +V Commands Detail 45
- +VTS Send Voice Tone(s) 46
- +VRN Ringback Timer 50
- Flow Control 57
- Voice Mode Result Codes 57
- Voice Mode Shielded Codes 59
- DTE/DCE Interface Rates 61
- Configuration 62
Relacionado con productos y manuales para Redes Multitech MT9234ZBAUSBCDC
Redes Multitech MTCBA-C-N12 Manual de usuario
(17 paginas)
(17 paginas)
Redes Multitech MTSMC-G-F1 Especificaciones
(26 paginas)
(26 paginas)
Redes Multitech MULTIVOIP MVP-810ST Guía de usuario
(559 paginas)
(559 paginas)
Redes Multitech MT9234ZPX-UPCI Especificaciones
(8 paginas)
(8 paginas)
Redes Multitech BL-Series Manual de usuario
(60 paginas)
(60 paginas)
Redes Multitech FaxFinder FF240-IP Especificaciones
(90 paginas)
(90 paginas)
Redes Multitech MT5656SMI Manual de usuario
(65 paginas)
(65 paginas)
Redes Multitech MT5634ZBA-USB Manual de usuario
(33 paginas)
(33 paginas)
Redes Multitech MTCBA-C-IP-N1 Especificaciones
(253 paginas)
(253 paginas)
Redes Multitech ISI5634UPCI/4 Guía de usuario
(22 paginas)
(22 paginas)
Redes Multitech GPRS Manual de usuario
(74 paginas)
(74 paginas)
Redes Multitech GFU19 Manual de usuario
(14 paginas)
(14 paginas)
Redes Multitech MT9234SMI-P-92 Especificaciones
(203 paginas)
(203 paginas)
Redes Multitech GPRS Guía de usuario
(29 paginas)
(29 paginas)
Redes Multitech BL-Series Manual de usuario
(60 paginas)
(60 paginas)
Redes Multitech rCell 500 Series Manual de usuario
(15 paginas)
(15 paginas)
Redes Multitech MT5656ZDX Series Guía de usuario
(55 paginas)
(55 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.322 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales