Multitech CDMA Especificaciones Pagina 28
- Pagina / 129
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 8 – Communication Commands
28 Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide
Fixed DTE Rate +IPR
Description: This command is used to specify the baud rate for the modem DATA port. The factory default
value is 115200.
Note: Auto-baud (automatic detection of DTE rate) is not supported.
At power-up, the interface rate is set to the value that was active when the last AT&W
command was used.
Note: The use of baud rates below 9600 may affect the operability of some software
features; e.g., TCP App.
Syntax: AT+IPR
Command
Possible Responses
AT+IPR?
Note: Read syntax.
+IPR: 9600
OK
Note: Current rate is 9600 bps
AT+IPR=115200
Note: Set interface rate to 115200 bps
OK
AT+IPR=?
Note: Lists supported <rate> values,[(list of
fixed-only <rate> values)]
(),(300,600,1200,2400,4800,9600,
19200,38400,57600,115200,230400)
OK
Note: Lists possible baud rates
AT+IPR
Note: Set interface rate to factory default
of 115200 bps
OK
DTE-DCE Local Flow Control +IFC
Description: This command is used to specify the UART flow control method. The factory default value is 2,2.
AT&F and AT&W are in effect. Software flow control is not supported.
Syntax: AT+IFC=<Tx>,<Rx>
Command
Possible Responses
AT+IFC=2,2
Note: Set values
OK
Note: New values set.
AT+IFC
Note: Set factory default values
OK
AT+IFC?
Note: Display current settings.
+IFC: 2,2
OK
AT+IFC=?
Note: Display valid parameter ranges.
+IFC: (0-3),(0-2)
OK
- CDMA-C1 AT Commands 1
- Copyright 2
- Trademarks 2
- Revisions 2
- Contacting Multi-Tech 2
- Contents 3
- Contents 4
- Document Scope 9
- Related References 9
- Serial Interface Settings 10
- Overview 10
- Terminology 11
- Command Format and Syntax 11
- Command-Line Editing 12
- Input Command Syntax 12
- Other Syntax 12
- Output Response Syntax 12
- Parameter Defaults 13
- Unsolicited Message Syntax 13
- Attention AT 14
- Repeat Last Command A/ 14
- Echo E 14
- +WUSLMSK 15
- Syntax: AT+WPRI? 16
- Hardware Version +WHWV 17
- Capabilities List +GCAP 19
- Subscriber Number +CNUM 19
- Save Configuration &W 21
- General Indicator +WIND 22
- Result 23
- Examples: +WIND: 4 23
- Error Codes: 24
- Chapter 7 – Status Commands 25
- Fixed DTE Rate +IPR 28
- Set DCD Signal &C 29
- Set DTR Signal &D 29
- Set DSR Signal &S 30
- Syntax: AT+DR=<val> 31
- Syntax: AT+WCHD 31
- Automatic Answer S0 32
- Command Edit Character S5 33
- Dial Command D 35
- Hang-Up Command H 36
- Answer a Call A 36
- Syntax: ATA 37
- Incoming Call +RING 38
- Emergency Mode +WSOS 40
- Call Answered +WANS 41
- Call Connected +WCNT 41
- Call Ended +WEND 42
- Call Originated +WORG 43
- CPHS Command +CPHS 43
- Values: <LineId> 44
- Examples: 44
- Call Forwarding +CCFC 45
- Syntax: AT+WFSH 46
- Unsolicited 46
- Send DTMF Tones +VTS 47
- Serving System +CSS 49
- Signal Quality +CSQ 50
- Band Preference +WBND 53
- Service Indication +WSRV 53
- Roam Preference +WRMP 54
- Default Cell Band +WDCB 55
- Roaming Indication +WROM 55
- Values: <indicator> 56
- Values: <mode> 58
- Excess SPC Failures +WLCK 60
- Commit Changes +WCMT 61
- Set IMSI +WIMI 62
- SID and NID +WSID 63
- Commit Successful +WOTC 66
- SPL Unlocked +WOTS 66
- NAM Download OK +WOTN 66
- MDM Download OK +WOTM 67
- IMSI Download OK +WOTI 67
- PRL Download OK +WOTP 67
- Values: <Mode> 74
- Parameter 74
- Send Message +CMGS 75
- Read Message +CMGR 76
- List Message +CMGL 77
- Delete Message +CMGD 79
- Syntax: +WMGF 84
- Audio Subsystem Overview 85
- Chapter 15 – Audio Commands 86
- Microphone Gain +VGT 87
- Speaker Gain Control +VGR 88
- Values: <Gain> 89
- Digital Gain Receive +WDGR 90
- Values: <val1> 91
- Echo Cancellation +ECHO 92
- Audio Loopback &T 94
- Quick Net Connect $QCQNC 95
- R-SCH Selection $QCMIP 96
- MIP Selection $QCMIPP 96
- Chapter 16 – Data Commands 97
- Configure TCP/IP +WIPCFG 99
- Values: <cmdtype> 101
- Bearer Status +WIPBR 102
- Values: <protocol> 103
- Response 105
- Syntax: AT+WIPERR? 105
- Values: 107
- Options and 107
- 32kHz Sleep Mode +W32K 110
- Chapter 18 – Sleep Commands 111
- Syntax: +WNETTIMEGET? 112
- Response Field 112
- Description: 112
- Introduction 113
- Acquiring Cellular Service 113
- Call Processing 114
- Sending Binary Data 115
- TCP Socket Examples 116
- TCP Client Socket Connection 117
- TCP Server Example 117
Relacionado con productos y manuales para Redes Multitech CDMA
Redes Multitech MT2834BA Manual de usuario
(7 paginas)
(7 paginas)
Redes Multitech ISIHP-2U El manual del propietario
(63 paginas)
(63 paginas)
Redes Multitech MT2834BL Especificaciones
(225 paginas)
(225 paginas)
Redes Multitech MT56DSU-R Manual de usuario
(11 paginas)
(11 paginas)
Redes Multitech MTSMC-C-N3 Manual de usuario
(14 paginas)
(14 paginas)
Redes Multitech MT2834ZDX Manual de usuario
(20 paginas)
(20 paginas)
Redes Multitech MVP30-60 Manual de usuario
(4 paginas)
(4 paginas)
Redes Multitech MULTIVOIP MVP-810 Guía de usuario
(163 paginas)
(163 paginas)
Redes Multitech FF830 Guía de usuario
(151 paginas)
(151 paginas)
Redes Multitech MTR-C2 Manual de usuario
(20 paginas)
(20 paginas)
Redes Multitech GFU19 Manual de usuario
(210 paginas)
(210 paginas)
Redes Multitech MTCMR-H Guía de usuario
(147 paginas)
(147 paginas)
Redes Multitech MTSMC-C-N3 Manual de usuario
(24 paginas)
(24 paginas)
Redes Multitech MT56DSU-R Especificaciones
(230 paginas)
(230 paginas)
Redes Multitech MTR-H6 Guía de usuario
(25 paginas)
(25 paginas)
Pfannenberg DTS 3181–400V / 460V manuals
Owner’s manuals and user’s guides for Conditioners Pfannenberg DTS 3181–400V / 460V.
We providing 1 pdf manuals Pfannenberg DTS 3181–400V / 460V for download free by document types: User Manual
Pfannenberg DTS 3181–400V / 460V User Manual (3 pages)
Brand: Pfannenberg | Category: Conditioners | Size: 0.27 MB |
Table of contents
More products and manuals for Conditioners Pfannenberg
| Models | Document Type |
|---|---|
| DTS 3181 SL–115V / 230V |
User Manual
Pfannenberg DTS 3181 SL–115V / 230V User Manual,
3 pages
|
| DTx 9021 115V 60Hz |
User Manual
Pfannenberg DTx 9021 115V 60Hz User Manual,
4 pages
|
| DTx 9021 230V 50/60Hz |
User Manual
Pfannenberg DTx 9021 230V 50/60Hz User Manual,
4 pages
|
| DTFI 9021 |
User Manual
 
Pfannenberg DTFI 9021 User Manual,
52 pages
|
| PWS Series |
User Manual
Pfannenberg PWS Series User Manual,
16 pages
|
| PAI |
User Manual
Pfannenberg PAI User Manual,
46 pages
|
| DTI 6x01 |
User Manual
Pfannenberg DTI 6x01 User Manual,
60 pages
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales