Multitech CDMA Especificaciones Pagina 86
- Pagina / 129
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 15 – Audio Commands
86 Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide
Speaker & Microphone Selection +SPEAKER
Description: This command is used to select the voice path, and activates a speaker/microphone audio path.
The modem supports one audio path: analog1. An audio path is functional only with appropriate
external hardware.
Voice paths may be changed while a call is in progress as well as in the idle state.
Syntax: AT+SPEAKER=<n>
Command
Possible Responses
AT+SPEAKER=0
Note: Select analog1 audio path.
OK
Note: Command valid.
AT+SPEAKER
Note: Select analog1 audio path.
OK
Note: Command valid (default
path)
AT+SPEAKER?
+SPEAKER: 0
OK
Note: analog1 audio path active.
AT+SPEAKER=?
Note: Get the range of values.
+SPEAKER: (0-2)
Values: < n >
0 Analog1 – LINE_IN and HPH_OUT. (default)
1 (not supported)
2 (not supported)
If no argument is supplied to the command, the default value is assumed. The configuration is
saved immediately. The Analog 1 output is designed to drive a 32Ω speaker. See the Audio
Overview section for more information.
Microphone Gain Enable +MGE
Description: This command enables or disables the 24dB microphone gain amplifier.
Syntax: AT+MGE=<val1>
Command
Possible Responses
AT+MGE
OK
Note: Sets default value of 0
AT+MGE=0
OK
Note: Disable amplifier
AT+MGE?
Note: Interrogate value
+MGE: 1
OK
Note: Current value
AT+MGE=?
Note: Test command
+MGE : (0-1)
OK
Note: Possible values
Values: <Gain>
0 Amplifier Disabled (0dB gain) (default)
1 Amplifier Enabled (24dB gain)
If no argument is supplied to the command, the default value is assumed. The configuration is
saved immediately. See the Audio Overview section for more information.
- CDMA-C1 AT Commands 1
- Copyright 2
- Trademarks 2
- Revisions 2
- Contacting Multi-Tech 2
- Contents 3
- Contents 4
- Document Scope 9
- Related References 9
- Serial Interface Settings 10
- Overview 10
- Terminology 11
- Command Format and Syntax 11
- Command-Line Editing 12
- Input Command Syntax 12
- Other Syntax 12
- Output Response Syntax 12
- Parameter Defaults 13
- Unsolicited Message Syntax 13
- Attention AT 14
- Repeat Last Command A/ 14
- Echo E 14
- +WUSLMSK 15
- Syntax: AT+WPRI? 16
- Hardware Version +WHWV 17
- Capabilities List +GCAP 19
- Subscriber Number +CNUM 19
- Save Configuration &W 21
- General Indicator +WIND 22
- Result 23
- Examples: +WIND: 4 23
- Error Codes: 24
- Chapter 7 – Status Commands 25
- Fixed DTE Rate +IPR 28
- Set DCD Signal &C 29
- Set DTR Signal &D 29
- Set DSR Signal &S 30
- Syntax: AT+DR=<val> 31
- Syntax: AT+WCHD 31
- Automatic Answer S0 32
- Command Edit Character S5 33
- Dial Command D 35
- Hang-Up Command H 36
- Answer a Call A 36
- Syntax: ATA 37
- Incoming Call +RING 38
- Emergency Mode +WSOS 40
- Call Answered +WANS 41
- Call Connected +WCNT 41
- Call Ended +WEND 42
- Call Originated +WORG 43
- CPHS Command +CPHS 43
- Values: <LineId> 44
- Examples: 44
- Call Forwarding +CCFC 45
- Syntax: AT+WFSH 46
- Unsolicited 46
- Send DTMF Tones +VTS 47
- Serving System +CSS 49
- Signal Quality +CSQ 50
- Band Preference +WBND 53
- Service Indication +WSRV 53
- Roam Preference +WRMP 54
- Default Cell Band +WDCB 55
- Roaming Indication +WROM 55
- Values: <indicator> 56
- Values: <mode> 58
- Excess SPC Failures +WLCK 60
- Commit Changes +WCMT 61
- Set IMSI +WIMI 62
- SID and NID +WSID 63
- Commit Successful +WOTC 66
- SPL Unlocked +WOTS 66
- NAM Download OK +WOTN 66
- MDM Download OK +WOTM 67
- IMSI Download OK +WOTI 67
- PRL Download OK +WOTP 67
- Values: <Mode> 74
- Parameter 74
- Send Message +CMGS 75
- Read Message +CMGR 76
- List Message +CMGL 77
- Delete Message +CMGD 79
- Syntax: +WMGF 84
- Audio Subsystem Overview 85
- Chapter 15 – Audio Commands 86
- Microphone Gain +VGT 87
- Speaker Gain Control +VGR 88
- Values: <Gain> 89
- Digital Gain Receive +WDGR 90
- Values: <val1> 91
- Echo Cancellation +ECHO 92
- Audio Loopback &T 94
- Quick Net Connect $QCQNC 95
- R-SCH Selection $QCMIP 96
- MIP Selection $QCMIPP 96
- Chapter 16 – Data Commands 97
- Configure TCP/IP +WIPCFG 99
- Values: <cmdtype> 101
- Bearer Status +WIPBR 102
- Values: <protocol> 103
- Response 105
- Syntax: AT+WIPERR? 105
- Values: 107
- Options and 107
- 32kHz Sleep Mode +W32K 110
- Chapter 18 – Sleep Commands 111
- Syntax: +WNETTIMEGET? 112
- Response Field 112
- Description: 112
- Introduction 113
- Acquiring Cellular Service 113
- Call Processing 114
- Sending Binary Data 115
- TCP Socket Examples 116
- TCP Client Socket Connection 117
- TCP Server Example 117
Relacionado con productos y manuales para Redes Multitech CDMA
Redes Multitech MT2834BA Manual de usuario
(7 paginas)
(7 paginas)
Redes Multitech ISIHP-2U El manual del propietario
(63 paginas)
(63 paginas)
Redes Multitech MT2834BL Especificaciones
(225 paginas)
(225 paginas)
Redes Multitech MT56DSU-R Manual de usuario
(11 paginas)
(11 paginas)
Redes Multitech MTSMC-C-N3 Manual de usuario
(14 paginas)
(14 paginas)
Redes Multitech MT2834ZDX Manual de usuario
(20 paginas)
(20 paginas)
Redes Multitech MVP30-60 Manual de usuario
(4 paginas)
(4 paginas)
Redes Multitech MULTIVOIP MVP-810 Guía de usuario
(163 paginas)
(163 paginas)
Redes Multitech FF830 Guía de usuario
(151 paginas)
(151 paginas)
Redes Multitech MTR-C2 Manual de usuario
(20 paginas)
(20 paginas)
Redes Multitech GFU19 Manual de usuario
(210 paginas)
(210 paginas)
Redes Multitech MTCMR-H Guía de usuario
(147 paginas)
(147 paginas)
Redes Multitech MTSMC-C-N3 Manual de usuario
(24 paginas)
(24 paginas)
Redes Multitech MT56DSU-R Especificaciones
(230 paginas)
(230 paginas)
Redes Multitech MTR-H6 Guía de usuario
(25 paginas)
(25 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales