Multitech CDMA Especificaciones Pagina 31
- Pagina / 129
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 8 – Communication Commands
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide 31
<P1>
512-2048 Specifies the maximum number of dictionary entries that should be negotiated.
Default is 2048.
<P2>
6 Specifies the maximum string length to be negotiated. Default is 6.
V.42bis Data Compression Report +DR
Description: This command returns the results of data compression capability. If data reporting is enabled,
this command returns the data compression type of an incoming or outgoing data call.
Otherwise, the command returns NONE.
The intermediate result code represents current DCE-DCE data compression type. The syntax for
+DR reporting is: +DR<result>, and the result code is defined as follows:
+DR: NONE
Data compression is not in use
+DR: V42B
Rec. V.42bis is in use in both directions
+DR: V42B RD
Rec. V.42bis is in use in receive direction only
+DR: V42B TD
Rec. V.42bis is in use in transmit direction only
The +DR intermediate result code, if enabled, is issued before the final result code and after the
service report control +CR.
Syntax: AT+DR=<val>
Command
Possible Responses
AT+DR=1
Note: Reporting enabled
OK
Note: Command valid
AT+DR?
Note: Display the current value
+DR: 1
OK
Note: Command valid
AT+DR=?
Note: Display the supported values
+DR: (0,1)
OK
Note: Command valid
Values: This syntax is for setting the +DR reporting method.
<val>
0 Disable reporting (Default)
1 Enable reporting
Hang-Up 1x Data Command +WCHD
Description: The AT+WCHD command is used by the application to disconnect all 1x data calls. The
alternative is to use the DTR pin.
Syntax: AT+WCHD
Command
Possible Responses
AT+WCHD
Note: Ask for disconnection
OK
NO CARRIER
- CDMA-C1 AT Commands 1
- Copyright 2
- Trademarks 2
- Revisions 2
- Contacting Multi-Tech 2
- Contents 3
- Contents 4
- Document Scope 9
- Related References 9
- Serial Interface Settings 10
- Overview 10
- Terminology 11
- Command Format and Syntax 11
- Command-Line Editing 12
- Input Command Syntax 12
- Other Syntax 12
- Output Response Syntax 12
- Parameter Defaults 13
- Unsolicited Message Syntax 13
- Attention AT 14
- Repeat Last Command A/ 14
- Echo E 14
- +WUSLMSK 15
- Syntax: AT+WPRI? 16
- Hardware Version +WHWV 17
- Capabilities List +GCAP 19
- Subscriber Number +CNUM 19
- Save Configuration &W 21
- General Indicator +WIND 22
- Result 23
- Examples: +WIND: 4 23
- Error Codes: 24
- Chapter 7 – Status Commands 25
- Fixed DTE Rate +IPR 28
- Set DCD Signal &C 29
- Set DTR Signal &D 29
- Set DSR Signal &S 30
- Syntax: AT+DR=<val> 31
- Syntax: AT+WCHD 31
- Automatic Answer S0 32
- Command Edit Character S5 33
- Dial Command D 35
- Hang-Up Command H 36
- Answer a Call A 36
- Syntax: ATA 37
- Incoming Call +RING 38
- Emergency Mode +WSOS 40
- Call Answered +WANS 41
- Call Connected +WCNT 41
- Call Ended +WEND 42
- Call Originated +WORG 43
- CPHS Command +CPHS 43
- Values: <LineId> 44
- Examples: 44
- Call Forwarding +CCFC 45
- Syntax: AT+WFSH 46
- Unsolicited 46
- Send DTMF Tones +VTS 47
- Serving System +CSS 49
- Signal Quality +CSQ 50
- Band Preference +WBND 53
- Service Indication +WSRV 53
- Roam Preference +WRMP 54
- Default Cell Band +WDCB 55
- Roaming Indication +WROM 55
- Values: <indicator> 56
- Values: <mode> 58
- Excess SPC Failures +WLCK 60
- Commit Changes +WCMT 61
- Set IMSI +WIMI 62
- SID and NID +WSID 63
- Commit Successful +WOTC 66
- SPL Unlocked +WOTS 66
- NAM Download OK +WOTN 66
- MDM Download OK +WOTM 67
- IMSI Download OK +WOTI 67
- PRL Download OK +WOTP 67
- Values: <Mode> 74
- Parameter 74
- Send Message +CMGS 75
- Read Message +CMGR 76
- List Message +CMGL 77
- Delete Message +CMGD 79
- Syntax: +WMGF 84
- Audio Subsystem Overview 85
- Chapter 15 – Audio Commands 86
- Microphone Gain +VGT 87
- Speaker Gain Control +VGR 88
- Values: <Gain> 89
- Digital Gain Receive +WDGR 90
- Values: <val1> 91
- Echo Cancellation +ECHO 92
- Audio Loopback &T 94
- Quick Net Connect $QCQNC 95
- R-SCH Selection $QCMIP 96
- MIP Selection $QCMIPP 96
- Chapter 16 – Data Commands 97
- Configure TCP/IP +WIPCFG 99
- Values: <cmdtype> 101
- Bearer Status +WIPBR 102
- Values: <protocol> 103
- Response 105
- Syntax: AT+WIPERR? 105
- Values: 107
- Options and 107
- 32kHz Sleep Mode +W32K 110
- Chapter 18 – Sleep Commands 111
- Syntax: +WNETTIMEGET? 112
- Response Field 112
- Description: 112
- Introduction 113
- Acquiring Cellular Service 113
- Call Processing 114
- Sending Binary Data 115
- TCP Socket Examples 116
- TCP Client Socket Connection 117
- TCP Server Example 117
Relacionado con productos y manuales para Redes Multitech CDMA
Redes Multitech MT2834BA Manual de usuario
(7 paginas)
(7 paginas)
Redes Multitech ISIHP-2U El manual del propietario
(63 paginas)
(63 paginas)
Redes Multitech MT2834BL Especificaciones
(225 paginas)
(225 paginas)
Redes Multitech MT56DSU-R Manual de usuario
(11 paginas)
(11 paginas)
Redes Multitech MTSMC-C-N3 Manual de usuario
(14 paginas)
(14 paginas)
Redes Multitech MT2834ZDX Manual de usuario
(20 paginas)
(20 paginas)
Redes Multitech MVP30-60 Manual de usuario
(4 paginas)
(4 paginas)
Redes Multitech MULTIVOIP MVP-810 Guía de usuario
(163 paginas)
(163 paginas)
Redes Multitech FF830 Guía de usuario
(151 paginas)
(151 paginas)
Redes Multitech MTR-C2 Manual de usuario
(20 paginas)
(20 paginas)
Redes Multitech GFU19 Manual de usuario
(210 paginas)
(210 paginas)
Redes Multitech MTCMR-H Guía de usuario
(147 paginas)
(147 paginas)
Redes Multitech MTSMC-C-N3 Manual de usuario
(24 paginas)
(24 paginas)
Redes Multitech MT56DSU-R Especificaciones
(230 paginas)
(230 paginas)
Redes Multitech MTR-H6 Guía de usuario
(25 paginas)
(25 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales