Multitech BL-Series Manual de usuario descargar pdf (Pagina 32)

AT Commands for the MT5656ZDX, MT5600ZDX, MT5600BA/BL-Series Modems

Multi-Tech Systems, Inc. Commands Reference Guide (PN S000273D)

V.8/V.8bis Commands

Command: +A8E V.8 and V.8bis Operation Controls

Description: This command is defined for two conditions: as a parameter while the modem is on-hook,

and as an action command while the modem is off-hook. If enabled, V.8 negotiation does

not preclude simultaneous implementation of other negotiation means (e.g., V.8bis, V.18,

V.32bis Annex A). It is a compound parameter if issued while the modem is on-hook, used

to precondition V.8 and V.8bis originating and answering operation. It is issued by the DTE

before the Dial (D) or Answer (A) command, regardless of the state of the +FCLASS

parameter. This command is an action command if issued while the modem is off-hook to

(re)start V.8 or V.8bis negotiation. Example: If initial V.8 negotiation fails, but subsequent

T.30 negotiation indicates V.8 capability, this command may be used to initiate V.8

negotiation.

Syntax: +A8E=<v8o>,<v8a>,<v8cf>[,<v8b>][,<cfrange>][,<protrange>]

Defined Values: <v8o> Decimal number which enables/disables issuance of +A8x indications during

modem-controlled V.8 origination negotiation.

1 Enable DCE-controlled V.8 origination negotiation without +A8x indications. Default.

6 Enable DCE-controlled V.8 origination negotiation with +A8x indications.

<v8a>= Decimal number which enables/disables issuance of +A8x indications during

modem-controlled V.8 answer negotiation.

1 Enable DCE-controlled V.8 answer negotiation without +A8x indications. Default.

5 Enable DCE-controlled V.8 answer negotiation with +A8x indications.

<v8cf>= Set the V.8 CI signal call function to the hexadecimal octet XY.

00 (Default.)

<v8b>= Decimal number which enables/disables V.8bis negotiation.

0 Disable V.8bis negotiation.

1 Enable V.8bis negotiation. Default.

<cfrange>= “<string of values>“. Applicable only for <v8a>=5. Not supported.

< protrange >= “<string of values>“. Applicable only for <v8a>=5. Not supported.

Default values: 1,1,00,1,0,0

The ATD and ATA commands behave as specified in V.250, and +A8n indications are not

generated by the modem.

For subparameter values <v8o>=6 and <v8a>=5, +A8I indications are issued during the V.8

session to notify the DTE when the relevant V.8 signals are received.

Reporting Current or Selected Values:

Command: +A8E?

Response: +A8E: <v8o>,<v8a>,<v8cf>[,<v8b>][,<cfrange>][,<protrange>]

Example: +A8E: 1,1,00,1,0,0 For the defaults

Reporting Supported Range of Parameter Values:

Command: +A8E=?

Response: +A8E: (<v8o> range),(<v8a> range),(v8cf in octets),

(<v8b> range),(<cfrange>),(<protrange>)

Example: +A8E: (1,6),(1,5),(0,21,C1),(0,1),(0),(0)

Command: +A8I CI Signal Indication

Description: This indication is issued by an answering modem, if +A8E,<v8a> .0, to indicate detection of

a V.8 CI signal, and report the recovered Call Function octet(s).

Indication Syntax: +A8I:<v8cf><CR>

Defined Values: <v8cf> A hexadecimal code octet representation of those Call Function octet(s). +A8I:0

indicates that the modem timed out waiting for CI.

Example: +A8I:0 The modem timed out waiting for CI.

+A8I:X YYY

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 59 60

Comentarios a estos manuales

Sin comentarios

Multitech BL-Series Manual de usuario Pagina 32

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Multitech BL-Series