Multitech MVPGK1 Guía de usuario Pagina 63
- Pagina / 87
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
64 MultiVOIP Gatekeeper User Guide
Power Saving Block Diagram
Suspend
Standby
On
Doze
Timer Control into Suspend
External Switch &
Timer Control into Suspend
Timer Control into Suspend
Timer Control into Doze
Timer Control into Standby
Timer Control
into Standby
Keyboard/Mouse
Wake-Up
Keyboard/Mouse Wake-Up
Keyboard/Mouse Wake-Up
Figure C-1: Power On & Three Reduced-Power States
CPU Doze Mode
1. After a pre-determined period of inactivity has elapsed, the CPU will slow to 8 MHz.
2. The computer will emit one beep sound.
3. The green function will monitor PC activity according to the settings on the Power Management
Setup screen.
4. As soon as any activity occurs, the system will switch from Doze Mode to On Mode.
System Standby Mode
1. After a predetermined period of inactivity has elapsed, the CPU will slow to 8 MHz.
2. The computer will emit two beeps.
3. The Level 1 cache will be disabled.
4. The VGA monitor will display a blank screen.
5. The hard drive will be powered down.
6. As soon as any activity occurs, the system will switch from Doze Mode to On Mode.
System Suspend Mode
1. After a pre-determined period of inactivity has elapsed, the CPU will slow to 8 MHz.
2. The computer will emit three beeps.
3. The Level 2 cache will be disabled.
4. The VGA monitor will display a blank screen.
5. The hard drive will be powered down.
6. The green function will monitor PC activity according to the settings on the Power Management
Setup screen.
7. When the system is in Suspend Mode, input from the keyboard, or the mouse, or alarm is required
to wake up the PC.
- MultiVOIP Gatekeeper 1
- Model MVPGK1 1
- Hardware User Guide 1
- User Guide 2
- Contents 3
- 6 Troubleshooting 35 4
- Appendices 45 4
- 1 Introduction/Description 5
- System Overview 6
- Technical Specifications 7
- SBC (Single Board Computer) 8
- Display: 9
- NIC Board (EN10100 PCI Card) 10
- Chapter 1 - System Overview 11
- 2 Installation and Setup 13
- Rack Mounting 15
- Cable Connections 15
- NIC Cabling 16
- SBC Board Cabling 16
- Powering Up 17
- 3 Single Board Computer 19
- Introduction 20
- Component Locations 21
- 4 PCI NIC Board 23
- About PCI Bus 25
- Features 25
- LED Indicators 26
- 5 Hardware Removal/ 27
- Replacement 27
- Card Cage Removal/Replacement 29
- GateKeeper 30
- Board Removal and Replacement 31
- Removing NIC Board 32
- 6 Troubleshooting 35
- Hardware Troubleshooting 36
- Chapter 6 - Troubleshooting 37
- Diagnostic Tests 38
- Calling Technical Support 39
- 7 Service, Warranty, and 40
- Technical Support 40
- Limited Warranty 41
- Ordering Accessories 42
- Tech Support 43
- About the Internet 43
- Appendices 44
- Pin Identification 45
- 6-Pin Circular Jack 46
- SBC Onboard Connectors 48
- Printer Port Connector 49
- COM 2 Port Connector 50
- Hard Disk Connector 50
- COM2 Connector 51
- External Keyboard Connector 51
- Reset Connector 51
- Floppy Disk Drive Connector 51
- Hard drive Connector 52
- Hard drive LED Connector 53
- Power Connector 53
- Expansion Slots 54
- ISA Bus Pin Assignments 55
- How to Set Jumpers 56
- Jumper Settings 57
- JP4 : CPU Clock Selection + 58
- Table B-4. DMA Channels Map 61
- Table B-5. Memory Map 61
- Table B-6. I/O Map 61
- Green PC Function 62
- Power Saving Block Diagram 63
- CPU Doze Mode 63
- System Standby Mode 63
- System Suspend Mode 63
- Award BIOS Setup 64
- Entering Setup 65
- SBC Configuration 66
- VGA Driver Utilities 67
- The BIOS Features Setup Menu 69
- Virus Warning 70
- Quick Power On Self Test 70
- Boot Sequence 70
- Boot Up Floppy Seek 70
- Boot Up NumLock Status 71
- Boot Up System Speed 71
- Gate A20 Option 71
- Typematic Rate Setting 71
- Typematic Rate (Chars/Sec) 71
- Chipset Features Setup 72
- DRAM Settings 73
- Cache Features 73
- PCI and IDE Configuration 73
- Power Management Setup 74
- Doze Mode 75
- Standby Mode 75
- PCI IRQ Activated by 76
- PCI IDE IRQ Map to 76
- Onboard PCI SCSI Chip 76
- Load BIOS Defaults 76
- Load Setup Defaults 76
- Integrated Peripherals 77
- Password Setting 77
- IDE HDD Auto Detection 78
- HDD Low Level Format 79
- Save & Exit Setup 80
- Canadian Limitations Notice 82
- Power Supply Unit 84
- Communication Module 84
- Carrier Card Expansion Card 84
- SITS/82/005S/D 85
- Compliance with BS6328 Part 1 85
- S0000122, Rev B 87
Relacionado con productos y manuales para Los componentes del chasis Multitech MVPGK1
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales