Multitech MVPGK1 Guía de usuario Pagina 65
- Pagina / 87
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
66 MultiVOIP Gatekeeper User Guide
Entering Setup
To enter the BIOS Setup screen, power on the computer and then press the Delete key immediately.
The other way to enter Setup is to power on the computer and then, when the below message appears
briefly at the bottom of the screen during the POST (Power On Self Test), press the Delete key or
simultaneously press <Ctrl>, < Alt >, and < Esc > keys (Control, Alternate, & Escape).
TO ENTER SETUP BEFORE BOOT PRESS <CTRL-ALT-ESC> OR <DEL> KEY
As long as the above message is present on the screen you may press the <Del> key (the one that
shares the decimal point at bottom of the number keypad) to access the Setup program. After a
moment, the main menu of the Award SETUP program will appear on the screen:
ROM / PCI / ISA BIOS (2A59FP6C)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
INTERGRATED PERIPHERALS
PASSWORD SETTING
IDE HDD AUTO DETECTION
HDD LOW LEVEL FORMAT
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
Esc: Quit
F10: Save & Exit Setup
(Shift) F2: Change Color
:SELECT ITEM
Time, Date, Hard Disk Type .........
Figure C-3. Setup Program Initial Screen
Setup Keyboard Commands
A common set of keyboard commands is used for all BIOS-related screens. For example, you may use
the cursor up/down keys to highlight the individual menu items. As you highlight each item, a brief
description of that items function will appear in the lower window. If you have a color monitor you can
use the Shift F2 keys to scroll through the various color combinations available.
In general, you use the arrow keys to highlight items and then press Enter to select. Use the PageUp
and PageDown keys to change entries. Press F1 for help. Press Esc to quit. The following table provides
more detail about how to navigate in the Setup program using the keyboard.
Up arrow Move to previous item
Down arrow Move to next item
Left arrow Move to the item in the left hand
Right arrow Move to the item in the right hand
Esc key Main Menu Quit but do not save changes into CMOS
Submenu Exit current page and return to Main Menu
PgUp key Increase the numeric value or make changes
PgDn key Decrease the numeric value or make changes
+ key Increase the numeric value or make changes
- key Decrease the numeric value or make changes
F1 key General help
- MultiVOIP Gatekeeper 1
- Model MVPGK1 1
- Hardware User Guide 1
- User Guide 2
- Contents 3
- 6 Troubleshooting 35 4
- Appendices 45 4
- 1 Introduction/Description 5
- System Overview 6
- Technical Specifications 7
- SBC (Single Board Computer) 8
- Display: 9
- NIC Board (EN10100 PCI Card) 10
- Chapter 1 - System Overview 11
- 2 Installation and Setup 13
- Rack Mounting 15
- Cable Connections 15
- NIC Cabling 16
- SBC Board Cabling 16
- Powering Up 17
- 3 Single Board Computer 19
- Introduction 20
- Component Locations 21
- 4 PCI NIC Board 23
- About PCI Bus 25
- Features 25
- LED Indicators 26
- 5 Hardware Removal/ 27
- Replacement 27
- Card Cage Removal/Replacement 29
- GateKeeper 30
- Board Removal and Replacement 31
- Removing NIC Board 32
- 6 Troubleshooting 35
- Hardware Troubleshooting 36
- Chapter 6 - Troubleshooting 37
- Diagnostic Tests 38
- Calling Technical Support 39
- 7 Service, Warranty, and 40
- Technical Support 40
- Limited Warranty 41
- Ordering Accessories 42
- Tech Support 43
- About the Internet 43
- Appendices 44
- Pin Identification 45
- 6-Pin Circular Jack 46
- SBC Onboard Connectors 48
- Printer Port Connector 49
- COM 2 Port Connector 50
- Hard Disk Connector 50
- COM2 Connector 51
- External Keyboard Connector 51
- Reset Connector 51
- Floppy Disk Drive Connector 51
- Hard drive Connector 52
- Hard drive LED Connector 53
- Power Connector 53
- Expansion Slots 54
- ISA Bus Pin Assignments 55
- How to Set Jumpers 56
- Jumper Settings 57
- JP4 : CPU Clock Selection + 58
- Table B-4. DMA Channels Map 61
- Table B-5. Memory Map 61
- Table B-6. I/O Map 61
- Green PC Function 62
- Power Saving Block Diagram 63
- CPU Doze Mode 63
- System Standby Mode 63
- System Suspend Mode 63
- Award BIOS Setup 64
- Entering Setup 65
- SBC Configuration 66
- VGA Driver Utilities 67
- The BIOS Features Setup Menu 69
- Virus Warning 70
- Quick Power On Self Test 70
- Boot Sequence 70
- Boot Up Floppy Seek 70
- Boot Up NumLock Status 71
- Boot Up System Speed 71
- Gate A20 Option 71
- Typematic Rate Setting 71
- Typematic Rate (Chars/Sec) 71
- Chipset Features Setup 72
- DRAM Settings 73
- Cache Features 73
- PCI and IDE Configuration 73
- Power Management Setup 74
- Doze Mode 75
- Standby Mode 75
- PCI IRQ Activated by 76
- PCI IDE IRQ Map to 76
- Onboard PCI SCSI Chip 76
- Load BIOS Defaults 76
- Load Setup Defaults 76
- Integrated Peripherals 77
- Password Setting 77
- IDE HDD Auto Detection 78
- HDD Low Level Format 79
- Save & Exit Setup 80
- Canadian Limitations Notice 82
- Power Supply Unit 84
- Communication Module 84
- Carrier Card Expansion Card 84
- SITS/82/005S/D 85
- Compliance with BS6328 Part 1 85
- S0000122, Rev B 87
Relacionado con productos y manuales para Los componentes del chasis Multitech MVPGK1
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales