Multitech MVPGK1 Guía de usuario Pagina 71
- Pagina / 87
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
72 MultiVOIP Gatekeeper User Guide
Boot Up NumLock Status
This enables you to determine the default state of the numeric keypad. By default, the system boots up
with NumLock on.
On Keypads number keys are active.
Off Keypads arrow keys are active.
Boot Up System Speed
Selects the default system speed the normal operating speed at power up.
High Sets the speed to high (default)
Low Sets the speed to low
Regardless of which setting is chosen, the operator can still use the turbo switch to toggle between
High and Low modes during operation.
Gate A20 Option
This entry enables you to select how gate A20 is handled. Gate A20 is a device used to address
memory above 1 Mbyte. Initially, Gate A20 was handled by a pin on the keyboard. Today, while
keyboards still provide this support, it is more common, and much faster, for the system chipset to
provide support for gate A20.
Normal keyboard (default)
Fast chipset
Typematic Rate Setting
Enable the typematic function if you want to be able to configure the key-repetition characteristics of
your keyboard. When typematic is disabled, continually holding down a key on your keyboard will
generate only one instance. In other words, the BIOS will only report that the key is down. When the
typematic rate is enabled, the BIOS will report as before, but it will then wait a moment, and, if the key
is still down, it will begin the report that the key has been depressed repeatedly. For example, you
would use such a feature to accelerate cursor movements with the arrow keys.
Enabled Enable typematic rate
Disabled Disable typematic rate (default)
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the typematic rate selection enables you select the rate at which
a held-down key will produce acceleration. Acceleration refers to multiple instances of a
character (letter, number, or symbol) or other multiple keyboard effects (like cursor movement with
arrow keys and character removal with the Delete keys).
6 6 characters per second (default)
8 8 characters per second
10 10 characters per second
12 12 characters per second
15 15 characters per second
20 20 characters per second
24 24 characters per second
- MultiVOIP Gatekeeper 1
- Model MVPGK1 1
- Hardware User Guide 1
- User Guide 2
- Contents 3
- 6 Troubleshooting 35 4
- Appendices 45 4
- 1 Introduction/Description 5
- System Overview 6
- Technical Specifications 7
- SBC (Single Board Computer) 8
- Display: 9
- NIC Board (EN10100 PCI Card) 10
- Chapter 1 - System Overview 11
- 2 Installation and Setup 13
- Rack Mounting 15
- Cable Connections 15
- NIC Cabling 16
- SBC Board Cabling 16
- Powering Up 17
- 3 Single Board Computer 19
- Introduction 20
- Component Locations 21
- 4 PCI NIC Board 23
- About PCI Bus 25
- Features 25
- LED Indicators 26
- 5 Hardware Removal/ 27
- Replacement 27
- Card Cage Removal/Replacement 29
- GateKeeper 30
- Board Removal and Replacement 31
- Removing NIC Board 32
- 6 Troubleshooting 35
- Hardware Troubleshooting 36
- Chapter 6 - Troubleshooting 37
- Diagnostic Tests 38
- Calling Technical Support 39
- 7 Service, Warranty, and 40
- Technical Support 40
- Limited Warranty 41
- Ordering Accessories 42
- Tech Support 43
- About the Internet 43
- Appendices 44
- Pin Identification 45
- 6-Pin Circular Jack 46
- SBC Onboard Connectors 48
- Printer Port Connector 49
- COM 2 Port Connector 50
- Hard Disk Connector 50
- COM2 Connector 51
- External Keyboard Connector 51
- Reset Connector 51
- Floppy Disk Drive Connector 51
- Hard drive Connector 52
- Hard drive LED Connector 53
- Power Connector 53
- Expansion Slots 54
- ISA Bus Pin Assignments 55
- How to Set Jumpers 56
- Jumper Settings 57
- JP4 : CPU Clock Selection + 58
- Table B-4. DMA Channels Map 61
- Table B-5. Memory Map 61
- Table B-6. I/O Map 61
- Green PC Function 62
- Power Saving Block Diagram 63
- CPU Doze Mode 63
- System Standby Mode 63
- System Suspend Mode 63
- Award BIOS Setup 64
- Entering Setup 65
- SBC Configuration 66
- VGA Driver Utilities 67
- The BIOS Features Setup Menu 69
- Virus Warning 70
- Quick Power On Self Test 70
- Boot Sequence 70
- Boot Up Floppy Seek 70
- Boot Up NumLock Status 71
- Boot Up System Speed 71
- Gate A20 Option 71
- Typematic Rate Setting 71
- Typematic Rate (Chars/Sec) 71
- Chipset Features Setup 72
- DRAM Settings 73
- Cache Features 73
- PCI and IDE Configuration 73
- Power Management Setup 74
- Doze Mode 75
- Standby Mode 75
- PCI IRQ Activated by 76
- PCI IDE IRQ Map to 76
- Onboard PCI SCSI Chip 76
- Load BIOS Defaults 76
- Load Setup Defaults 76
- Integrated Peripherals 77
- Password Setting 77
- IDE HDD Auto Detection 78
- HDD Low Level Format 79
- Save & Exit Setup 80
- Canadian Limitations Notice 82
- Power Supply Unit 84
- Communication Module 84
- Carrier Card Expansion Card 84
- SITS/82/005S/D 85
- Compliance with BS6328 Part 1 85
- S0000122, Rev B 87
Relacionado con productos y manuales para Los componentes del chasis Multitech MVPGK1
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales