Multitech MTPSR1-202ST Guía de usuario descargar pdf (Pagina 16)

ProxyServer User Guide

MTPSR1-202ST

Introduction

This chapter covers procedures for loading the ProxyServer software from a Windows PC (Win95 or

Win3.1x) and configuring your ProxyServer. Configuration includes setting up the LAN and WAN port

IP addresses, setting up the ISDN configuration default parameters, then downloading the default

setup to the target ISDN ProxyServer.

Before You Start Loading your Software

Consider the following choices before you configure your ProxyServer and record your selections on

the following pages; then refer to them while loading your software.

Network Configuration

Network Switch Type_________________________________________

Select the network switch type your ISDN service provider uses at its local central office. You can set

the ProxyServer to NET3 (DSS1), 1TR6, VN4, INS64, NI-1, AT&T 5ESS, or DMS-100. If you do not

know the switch type, you can get the information from your ISDN service provider.

Data TEI_____________________________________________________

The Data TEI is the TEI that is assigned to the data channel. You can select “Auto TEI,” a fixed TEI,

number (from 0 to 63), or “Disabled.” A TEI (terminal endpoint identifier) is a number used by the central

office switch to uniquely identify each device that is connected to the network. When it uses dynamic

TEI assignments (Auto TEI), the central office switch assigns a TEI each time the ProxyServer connects

to the network. However, the ISDN service provider may assign a fixed TEI at subscription time, in

which case you must configure the ProxyServer with the fixed TEI number. You can also disable the

channel, which may be useful when multiple ProxyServers are attached to a network terminator bus.

Voice TEI___________________________________________________

The Voice TEI is the TEI assigned to the voice channel. You have the same choices as for the Voice

TEI: “Auto TEI,” a fixed TEI number (from 0 to 63), or “Disabled.”

Data SPID__________________________________________________

The ProxyServer must be configured with the Service Profile Identifier (SPID). The data SPID is

assigned by the local phone company and is for the specific BRI line to which the ProxyServer will be

attached. The data SPID string can have up to 20 characters. The data SPID is not used if the

switch type is set to NET3.

Note: For DMS-100 switches, any ASCII character except the underline (_) character is valid. For

NI-1 and AT&T switches, only the digits 0-9 are valid.

Voice SPID__________________________________________________

The voice SPID is assigned by the local phone company and is for the specific BRI line to which the

ProxyServer will be attached. The voice SPID string can have up to 20 characters. The data SPID is

not used if the switch type is set to NET3.

Note: For DMS-100 switches, any ASCII character except the underline (_) character is valid. For

NI-1 and AT&T switches, only the digits 0-9 are valid.

Data Directory Number________________________________________

The data Directory Number (DN) is a telephone number that is assigned to the ProxyServer at

subscription time by the ISDN service provider. The DN is a string of up to 24 characters; valid

characters are 0-9, the * character, and the # character.

Voice Directory Number_______________________________________

The voice Directory Number (DN) is a telephone number that is assigned to the ProxyServer at

subscription time by the ISDN service provider. The DN is a string of up to 24 characters; valid

characters are 0-9, the * character, and the # character.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 103 104

Comentarios a estos manuales

Sin comentarios

Multitech MTPSR1-202ST Guía de usuario Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Multitech MTPSR1-202ST