Multitech MTS2BTA-R Manual de usuario Pagina 27
- Pagina / 88
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2 – AT Commands
Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360H) 27
SW23 Write PIO Level
This command sets the PIO logic level.
Format: ATSW23,<PIO#>,<Value>,<Store>
Parameters: ATSW23,<PIO#>,<Value>,<Store>
• PIO#: 3,6,7 (6 & 7 not user controllable in MP mode, see notes above in
ATSW22)
• PIO State:
0 = Off (0V)
1 = On (+V)
• Store:
0 = Do Not Store
1 = Store Parameters in Flash
EXAMPLE:
TYPE: ATSW23,6,1,1<cr>
REPLY: <cr_lf>OK<cr_lf>
OR
<cr_lf>ERROR<cr_lf>
Read Using: ATSR21
SW24 Write Response, Security, Auto SCO, Filter Settings
This command configures response, security, auto SCO, and filter settings.
Format: ATSW24,<Response Type>,<Security>,<Auto SCO>,<Minor Filter>
Parameters: >
• Response Type (See Appendix B for more information):
0 = Long Response
1 = Short Response
2 = No Verbose Mode (No unsolicited responses will be output)
No OKs will come back, but requested information such as ATSI,
ATRSW, ATRSN and ATDI responses will.
The device will not output CONNECT or DISCONNECT messages.
In FTP and OPP modes the radio will still output all necessary
messages such as PUSH START and PUSH COMPLETE.
• Security: 56-bit encryption is automatically enabled when set to 1.
UART will reply PAIRED,<BT Address> before the CONNECT,<BT Address> is
returned when a connection is made.
0 = No Authorization
1 = Authorization Required
Note: If security is enabled in multipoint mode, all connected slaves will have to
use the same PIN. There is no way to assign an individual PIN to each slave.
• Auto SCO:
0 = No Automatic SCO Connect
1 = SCO Auto Connect Upon Radio Connect.
• Minor Filter:
0 = Disable Minor COD Filter on Inquiry
1 = Enable Minor COD Filter on Inquiry
Note: With the minor filter enabled, inquiry results are filtered by the lower 2
bytes of the COD. If the minor filter is disabled all devices are found.
Factory Default: Response Type = 0, Security = 0, Auto SCO = 0, Filter = 0
EXAMPLE:
TYPE: ATSW24,0,0,0,0<cr>
REPLY: <cr_lf>OK<cr_lf>
OR
<cr_lf>ERROR<cr_lf>
Read Using: ATSI,6
Notes: See Appendix B for differences between short and long response mode.
Requires a reset for security to go into affect.
- AT Commands 1
- Reference Guide 1
- Table of Contents 3
- Chapter 1 – Introduction 5
- Changing Configuration 6
- Using Multi-Point Mode 8
- Multipoint Examples 9
- Multi-Point Test Scenarios 10
- Repeater Mode 12
- Chapter 2 - AT Commands 13
- URST Reset 14
- FRST Factory Reset 14
- SI Status Information 15
- Security Commands 19
- Set and Read Device Name 20
- RSN Read Service Name 21
- SP Set PIN 22
- OP Overwrite PIN 23
- Configuration Commands 24
- SW22 Write PIO Direction 26
- SW23 Write PIO Level 27
- SW26 Lock User Settings 29
- SW27 Write LED Rate 29
- SW29 Write PIN Lock Mode 30
- SW30 Write Deep Sleep Mode 30
- Inquiry Commands 31
- Connect as Master Commands 32
- DC Dial Channel 33
- DL Dial Last 34
- LAST Read Last Address 34
- MACLR Master Address Clear 35
- Connect As Slave Command 36
- Disconnect Commands 36
- About Command/Data Mode 37
- Data Mode Commands 37
- Utilities – Cancel Command 38
- Pairing Commands 39
- Low Power Modes Using Sniff 40
- SNIFF Enable Sniff 40
- SSNIFF Enable Auto Sniff 41
- CSNIFF Clear Sniff 41
- XSNIFF Exit Sniff Mode 41
- PARK Enable Park 42
- XPARK Exit Park 42
- Golden Receive Power Range 42
- RSSI Get RSSI Value 42
- LQ Get Link Quality 43
- Max Power Command 44
- Variable Storage Commands 45
- PIO Logic Commands 46
- Commands 47
- FTP Client 48
- DHFTP Dial Hang Up FTP 49
- FTPB FTP Browse 49
- FTP Push/Pull Commands 51
- FTP Server 52
- DOPP Dial OPP 53
- DHOPP Dial Hang Up OPP 53
- OPP Push/Pull Commands 54
- Chapter 4 – Examples 59
- From Power Up 60
- Headset Point-to-Point 60
- Headset Multipoint 60
- Example Client Applications 61
- Description Requires 69
- Appendix B – Responses 72
- Appendix C -- UUID Table 79
- Consumption 80
- Command Responses Comparison 81
- Abbreviations 85
Relacionado con productos y manuales para No Multitech MTS2BTA-R
No Multitech ISI551PC El manual del propietario
(31 paginas)
(31 paginas)
No Multitech MTS2BTA-R Especificaciones
(12 paginas)
(12 paginas)
No Multitech ISI552PC El manual del propietario
(28 paginas)
(28 paginas)
No Multitech MR4800E Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales