Multitech MTS2BTA-R Manual de usuario Pagina 72
- Pagina / 88
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix B – Responses
Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360H) 72
Appendix B – Responses
Notes on Short Response Mode Structure:
• The first number (2-3 digits) returned identifies the command that was sent. All identifiers are unique to
each specific command except for commands such as ATSSN and ATSSNC. These have the same basic
function, only ATSSN is for point-to-point and ATSSNC is for multi-point use. In this case, the identifiers
will be the same.
• The second number (2 digits) returned after the comma is the response code. If the response code is 00
(“OK” in long response mode), then the command has been successfully received by the radio. This does
not mean the command is complete, but just that it has been accepted by the radio, as some commands
may not go into effect or return data immediately. Anything other than a 00 returned in the second
position means there was an error with the command.
• Any data returned after the second number will vary based on the command entered. See the response
table below for data formatting.
Response Table:
All example responses shown are with factory default settings in place. See AT Commands section for
description of returned parameters.
AT
Command
Example Long Response Example Short Response
Attention Prefix
AT <cr_lf>OK<cr_lf> <cr_lf>107,00<cr_lf>
Firmware Version
ATVER,ver1 <cr_lf>OK<cr_lf><cr_lf>Ver 3.6.2.1.0.0<cr_lf> <cr_lf>52,00,Ver 3.6.2.1.0.0<cr_lf>
Resetting
ATURST No Response No Response
ATFRST <cr_lf>OK<cr_lf><cr_lf>RESET
COMPLETE<cr_lf>
<cr_lf>75,00<cr_lf><cr_lf>RESET
COMPLETE<cr_lf>
<cr_lf>ERROR<cr_lf> <cr_lf>75,01<cr_lf>
ATSSW,0 <cr_lf>OK<cr_lf> <cr_lf>102,00 <cr_lf>
<cr_lf>ERROR<cr_lf> <cr_lf>102,01<cr_lf>
ATRSW,0 <cr_lf>OK<cr_lf><cr_lf>0<cr_lf> <cr_lf>103,00,00<cr_lf>
Boot Mode
ATSSW,1 <cr_lf>OK<cr_lf> <cr_lf>102,00<cr_lf>
<cr_lf>ERROR<cr_lf> <cr_lf>102,01<cr_lf>
ATRSW,1 <cr_lf>OK<cr_lf> <cr_lf>103,00,00<cr_lf>
Security Level
ATSSW,2 <cr_lf>OK<cr_lf> <cr_lf>102,00<cr_lf>
<cr_lf>ERROR<cr_lf> <cr_lf>102,01<cr_lf>
ATRSW,2 <cr_lf>OK<cr_lf> <cr_lf>103,00,00<cr_lf>
Get Status
ATSI,1 <cr_lf>OK<cr_lf><cr_lf>00A09608F513<cr_lf> <cr_lf>14,00,123456789012<cr_lf>
ATSI,2 <cr_lf>OK<cr_lf><cr_lf>SocketWireless<cr_lf> <cr_lf>53,00,0A,SocketWireless<cr_lf>
ATSI,3 <cr_lf>OK<cr_lf><cr_lf>0,0<cr_lf> <cr_lf>17,00,0,0<cr_lf>
- AT Commands 1
- Reference Guide 1
- Table of Contents 3
- Chapter 1 – Introduction 5
- Changing Configuration 6
- Using Multi-Point Mode 8
- Multipoint Examples 9
- Multi-Point Test Scenarios 10
- Repeater Mode 12
- Chapter 2 - AT Commands 13
- URST Reset 14
- FRST Factory Reset 14
- SI Status Information 15
- Security Commands 19
- Set and Read Device Name 20
- RSN Read Service Name 21
- SP Set PIN 22
- OP Overwrite PIN 23
- Configuration Commands 24
- SW22 Write PIO Direction 26
- SW23 Write PIO Level 27
- SW26 Lock User Settings 29
- SW27 Write LED Rate 29
- SW29 Write PIN Lock Mode 30
- SW30 Write Deep Sleep Mode 30
- Inquiry Commands 31
- Connect as Master Commands 32
- DC Dial Channel 33
- DL Dial Last 34
- LAST Read Last Address 34
- MACLR Master Address Clear 35
- Connect As Slave Command 36
- Disconnect Commands 36
- About Command/Data Mode 37
- Data Mode Commands 37
- Utilities – Cancel Command 38
- Pairing Commands 39
- Low Power Modes Using Sniff 40
- SNIFF Enable Sniff 40
- SSNIFF Enable Auto Sniff 41
- CSNIFF Clear Sniff 41
- XSNIFF Exit Sniff Mode 41
- PARK Enable Park 42
- XPARK Exit Park 42
- Golden Receive Power Range 42
- RSSI Get RSSI Value 42
- LQ Get Link Quality 43
- Max Power Command 44
- Variable Storage Commands 45
- PIO Logic Commands 46
- Commands 47
- FTP Client 48
- DHFTP Dial Hang Up FTP 49
- FTPB FTP Browse 49
- FTP Push/Pull Commands 51
- FTP Server 52
- DOPP Dial OPP 53
- DHOPP Dial Hang Up OPP 53
- OPP Push/Pull Commands 54
- Chapter 4 – Examples 59
- From Power Up 60
- Headset Point-to-Point 60
- Headset Multipoint 60
- Example Client Applications 61
- Description Requires 69
- Appendix B – Responses 72
- Appendix C -- UUID Table 79
- Consumption 80
- Command Responses Comparison 81
- Abbreviations 85
Relacionado con productos y manuales para No Multitech MTS2BTA-R
No Multitech ISI551PC El manual del propietario
(31 paginas)
(31 paginas)
No Multitech MTS2BTA-R Especificaciones
(12 paginas)
(12 paginas)
No Multitech ISI552PC El manual del propietario
(28 paginas)
(28 paginas)
No Multitech MR4800E Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.565 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales