Multitech MTS2BTA-R Manual de usuario Pagina 53
- Pagina / 88
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2 – AT Commands
Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360H) 53
OPP Client Commands Introduction
The following OPP (Object Push Profile) commands allow the radio to be used as an OPP client, enabling it
to manipulate files on an OPP server. As the client, the device will initiate the connection with the server;
e.g., a PC, PDA, or cell phone. After making a connection, the device can push and pull objects.
Note: To achieve the maximum data throughput of 30kbps in OPP client mode, execute an ATUCL
command prior to making an OPP connection to put the radio in idle mode. If the radio is not in idle mode,
the data throughput will be approximately 15kbps.
OPP Connect/Disconnect Commands
DOPP Dial OPP
This command creates a connection to the OPP service on a remote device. Once this command
has been sent, the device cannot make any other connection until the OPP connection is
disconnected.
Format: ATDOPP,<BT Address>
Parameters: BT Address: Bluetooth Address, 12 hex characters MAX
Return Parameters: <BT Address>
EXAMPLE:
TYPE: ATDOPP,123456789012<cr>
REPLY: <cr_lf>OK<cr_lf>
<cr_lf>OPP CONNECT,123456789012<cr_lf>
OR
<cr_lf>OK<cr_lf>
<cr_lf>PAIRED,123456789012<cr_lf> // if security is
enabled
<cr_lf>OPP CONNECT,123456789012<cr_lf>
OR
<cr_lf>OK<cr_lf>
<cr_lf>OPP NO ANSWER<cr_lf> // if device not present
Notes:
• If the remote slave device is not present or the service is not available, OPP NO
ANSWER will reply after the master connect timeout and you will have to try again.
• If security is enabled and the radio is connecting to a laptop that has not yet been
paired with it, the <cr_lf>PAIRED,12345678912<cr_lf> message may return twice prior
to the OPP CONNECT.
• By default you will be located in the Bluetooth Exchange Folder of the remote device,
this will be the root directory.
• After making an OPP connection the radio will still be in command mode, not data
mode.
DHOPP Dial Hang Up OPP
This command will disconnect the current OPP connection.
Format: ATDHOPP
EXAMPLE:
TYPE: ATDHOPP
REPLY: <cr_lf>OK<cr_lf>
<cr_lf>OPP DISCONNECT<cr_lf>
OR
<cr_lf>ERROR<cr_lf>
- AT Commands 1
- Reference Guide 1
- Table of Contents 3
- Chapter 1 – Introduction 5
- Changing Configuration 6
- Using Multi-Point Mode 8
- Multipoint Examples 9
- Multi-Point Test Scenarios 10
- Repeater Mode 12
- Chapter 2 - AT Commands 13
- URST Reset 14
- FRST Factory Reset 14
- SI Status Information 15
- Security Commands 19
- Set and Read Device Name 20
- RSN Read Service Name 21
- SP Set PIN 22
- OP Overwrite PIN 23
- Configuration Commands 24
- SW22 Write PIO Direction 26
- SW23 Write PIO Level 27
- SW26 Lock User Settings 29
- SW27 Write LED Rate 29
- SW29 Write PIN Lock Mode 30
- SW30 Write Deep Sleep Mode 30
- Inquiry Commands 31
- Connect as Master Commands 32
- DC Dial Channel 33
- DL Dial Last 34
- LAST Read Last Address 34
- MACLR Master Address Clear 35
- Connect As Slave Command 36
- Disconnect Commands 36
- About Command/Data Mode 37
- Data Mode Commands 37
- Utilities – Cancel Command 38
- Pairing Commands 39
- Low Power Modes Using Sniff 40
- SNIFF Enable Sniff 40
- SSNIFF Enable Auto Sniff 41
- CSNIFF Clear Sniff 41
- XSNIFF Exit Sniff Mode 41
- PARK Enable Park 42
- XPARK Exit Park 42
- Golden Receive Power Range 42
- RSSI Get RSSI Value 42
- LQ Get Link Quality 43
- Max Power Command 44
- Variable Storage Commands 45
- PIO Logic Commands 46
- Commands 47
- FTP Client 48
- DHFTP Dial Hang Up FTP 49
- FTPB FTP Browse 49
- FTP Push/Pull Commands 51
- FTP Server 52
- DOPP Dial OPP 53
- DHOPP Dial Hang Up OPP 53
- OPP Push/Pull Commands 54
- Chapter 4 – Examples 59
- From Power Up 60
- Headset Point-to-Point 60
- Headset Multipoint 60
- Example Client Applications 61
- Description Requires 69
- Appendix B – Responses 72
- Appendix C -- UUID Table 79
- Consumption 80
- Command Responses Comparison 81
- Abbreviations 85
Relacionado con productos y manuales para No Multitech MTS2BTA-R
No Multitech ISI551PC El manual del propietario
(31 paginas)
(31 paginas)
No Multitech MTS2BTA-R Especificaciones
(12 paginas)
(12 paginas)
No Multitech ISI552PC El manual del propietario
(28 paginas)
(28 paginas)
No Multitech MR4800E Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales