Multitech MTS2BTA-R Manual de usuario Pagina 30
- Pagina / 88
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2 – AT Commands
Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360H) 30
SW29 Write PIN Lock Mode
The command configures the PIN lock setting.
Format: ATSW29,<PIN>,<Lock Mode>
Parameters:
• PIN: 16 alphanumeric characters MAX (Caps Sensitive, includes spaces)
• Lock Setting:
0 = In Normal operation ATOP is disabled
1 = Allow ATOP through UART only
2 = Allow ATOP through UART and over RF Link
Factory Default: 0
EXAMPLE:
TYPE: ATSW29,default,1<cr>
REPLY: <cr_lf>OK<cr_lf>
OR
<cr_lf>ERROR<cr_lf>
Read Using: ATSI,15
Note: This command enables ATOP, described in the Security PIN Settings section.
SW30 Write Deep Sleep Mode
This command configures the deep sleep mode.
Format: ATSW30,<Deep Sleep Mode>
Parameters:
• Deep Sleep Mode:
0 = Normal Operation never go into deep sleep
1 = Go into deep sleep whenever possible (While idle, page scan or sniff mode)
Factory Default: 0
EXAMPLE:
TYPE: ATSW30,1<cr>
REPLY: <cr_lf>OK<cr_lf>
OR
<cr_lf>ERROR<cr_lf>
Read Using: ATSI,16
Notes:
• When the radio is in deep sleep you can not discover or connect to it.
• The UART RX line needs to be pulled high if not active before power is applied to the
radio module.
• If there is an active UART RF link the device will need Sniff Mode enabled to allow it to
drop into sleep mode when there is no traffic.
• When in deep sleep, the UART will miss the first character while waking up. Send a
preamble byte to allow it to wake up and immediately thereafter send the AT Command
or data in less than 1 second or the device will go back to deep sleep again. If you are
using PIO(3) CPU interrupt a preamble byte is not needed.
• No bytes are lost if sending commands down over the remote RF link side.
• This setting is stored in flash and does not require a reset to take affect. Takes approx. 1
second before the current will drop down to 25-50uA. Allow 5msec. for the CPU unit to
come out of deep sleep.
• ATSW21,4096,18,4096,18 settings along with enabling Deep Sleep Mode will result in an
unconnected slave current draw of ≈ 350uA average.
- AT Commands 1
- Reference Guide 1
- Table of Contents 3
- Chapter 1 – Introduction 5
- Changing Configuration 6
- Using Multi-Point Mode 8
- Multipoint Examples 9
- Multi-Point Test Scenarios 10
- Repeater Mode 12
- Chapter 2 - AT Commands 13
- URST Reset 14
- FRST Factory Reset 14
- SI Status Information 15
- Security Commands 19
- Set and Read Device Name 20
- RSN Read Service Name 21
- SP Set PIN 22
- OP Overwrite PIN 23
- Configuration Commands 24
- SW22 Write PIO Direction 26
- SW23 Write PIO Level 27
- SW26 Lock User Settings 29
- SW27 Write LED Rate 29
- SW29 Write PIN Lock Mode 30
- SW30 Write Deep Sleep Mode 30
- Inquiry Commands 31
- Connect as Master Commands 32
- DC Dial Channel 33
- DL Dial Last 34
- LAST Read Last Address 34
- MACLR Master Address Clear 35
- Connect As Slave Command 36
- Disconnect Commands 36
- About Command/Data Mode 37
- Data Mode Commands 37
- Utilities – Cancel Command 38
- Pairing Commands 39
- Low Power Modes Using Sniff 40
- SNIFF Enable Sniff 40
- SSNIFF Enable Auto Sniff 41
- CSNIFF Clear Sniff 41
- XSNIFF Exit Sniff Mode 41
- PARK Enable Park 42
- XPARK Exit Park 42
- Golden Receive Power Range 42
- RSSI Get RSSI Value 42
- LQ Get Link Quality 43
- Max Power Command 44
- Variable Storage Commands 45
- PIO Logic Commands 46
- Commands 47
- FTP Client 48
- DHFTP Dial Hang Up FTP 49
- FTPB FTP Browse 49
- FTP Push/Pull Commands 51
- FTP Server 52
- DOPP Dial OPP 53
- DHOPP Dial Hang Up OPP 53
- OPP Push/Pull Commands 54
- Chapter 4 – Examples 59
- From Power Up 60
- Headset Point-to-Point 60
- Headset Multipoint 60
- Example Client Applications 61
- Description Requires 69
- Appendix B – Responses 72
- Appendix C -- UUID Table 79
- Consumption 80
- Command Responses Comparison 81
- Abbreviations 85
Relacionado con productos y manuales para No Multitech MTS2BTA-R
No Multitech ISI551PC El manual del propietario
(31 paginas)
(31 paginas)
No Multitech MTS2BTA-R Especificaciones
(12 paginas)
(12 paginas)
No Multitech ISI552PC El manual del propietario
(28 paginas)
(28 paginas)
No Multitech MR4800E Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales