Multitech MTCMR-E1 Manual de usuario Pagina 49
- Pagina / 119
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Part 1 – AT Commands for All Universal IP Devices
Universal IP AT Commands Reference Guide 49
Responses: \r\n#UDPDLEMODE: VALUE\r\n
\r\nOK\r\n
\r\nERROR\r\n
Example(s): send: AT#UDPDLEMODE=0\r
reply: \r\nOK\r\n
send: AT#UDPDLEMODE?\r
reply: \r\n#UDPDLEMODE: 0\r\n
reply: \r\nOK\r\n
#LUDPSTART – Initiate the UDP Session in Listen Mode
Description: Once an IP link is established, and if no other TCP/IP stack resource is active, this command sent
by the attached host directs the TCP/IP stack to initiate the UDP session in listen mode on the
specified UDP local port UDPPORT.
Syntax: AT#LUDPSTART
Values: UDPPORT
UDPSESRV
UDPTXDELAY
Default: No default
#LUDPSTOP – Close UDP Listening Mode
Description: This command directs the TCP/IP stack to close a UDP listening mode session previously
launched by the AT#UDPSTART command.
Syntax: AT#LUDPSTOP
Values: UDPPORT (No default)
#OUTPORT – UDP/TCP Local Port Number
Description: Controls the local port that the UDP/TCP connection is bound to.
Syntax: SAT#OUTPORT=<Port Number value>
AT#OUTPORT? Read or display the current setting.(or AT#VALL).
Values: Set the port number local connection will use:
From 1 to 5 numeric digits (0 to 9). Note that numbers above 65,535 are illegal since port
identification fields are 16-bits long in the IDP header.
Default: 37500
#OUDP – Initiate UDP Session in Active Mode
Description: Once an IP link is established, and if no other TCP/IP stack resource is active, this command sent
by the attached host directs the TCP/IP stack to initiate an UDP session in active mode on the
specified UDP remote port UDPPORT to the specified remote IP address UDPSERV.
The host can then transmit to the UDPPORT or UDPSERV address. Datagrams can only be
received from this UDPPORT or UDPSERV address.
Syntax: AT#UDPOPEN
Values: UDPPORT
UDPSERV
UDPTXDELAY
Default: No default
- Universal IP 1
- Contacting Multi-Tech 2
- Contents 3
- Part 1 – AT Commands 10
- Set Commands 11
- &D – DTR Option 12
- &S – DSR ON or OFF 12
- <parity> 13
- +IFC – Set Flow Control 14
- +IPR – Set Serial Speed 14
- Display Commands 16
- Syntax: AT#VALL 18
- Responses – MT100SEM-IP only 18
- #RECiADD – Set Email Address 21
- #SMTPPW – Set SMTP Password 23
- #SMTPUN – Set SMTP User Name 23
- #POP3UN – Set POP3 User Name 28
- Display Command 29
- #FTPUN – Set FTP User Name 31
- #FTPPW – Set FTP Password 31
- Chapter 4 – FTP AT Commands 32
- #TCPTXDELAY – Time Delay 36
- Chapter 5 – TCP AT Commands 38
- Chapter 6 – UDP AT Commands 46
- #UDPPORT – UDP Port Number 47
- #UDPDLEMODE – Set DLE Mode 48
- Part 2 – AT Commands for the 53
- Part 3 – AT Commands 60
- Chapter 10 – IP AT Commands 62
- #WLANSSID – SSID of WLAN 70
- Chapter 13–WLAN AT Commands 72
- #WLAN? – WLAN Module 77
- Part 4 – 78
- Chapter 14 – AT Commands 80
- #ISPPW – Set ISP Password 84
- #ISPUN – Set ISP User Name 85
- Part 5 – GPIO AT Commands 91
- About GPIO 92
- Part 6 – AT Commands 95
- #GPSPORT – Set GPS Host Port 96
- - Disable 99
- (Disabled) 99
- GPS Message Syntax 100
- GPS Message Examples 101
- GPS Configuration Examples 101
- Introduction 102
- NMEA Protocol Overview 102
- SUPPORTED MESSAGE LIST 102
- NMEA MESSAGES 103
- GLL – Latitude/Longitude 104
- Part 7 – Appendixes 107
- Response Messages 108
- Error Codes 109
- Commands 110
- Responses 110
- TCP Socket Response Messages 112
- Act as a TCP Client: AT#OTCP 113
Relacionado con productos y manuales para Redes Multitech MTCMR-E1
Redes Multitech MTCMR-G2 Guía de usuario
(56 paginas)
(56 paginas)
Redes Multitech MT2834ZPX Guía de usuario
(15 paginas)
(15 paginas)
Redes Multitech MT56DSU2 El manual del propietario
(39 paginas)
(39 paginas)
Redes Multitech MTCBA-C Guía de usuario
(16 paginas)
(16 paginas)
Redes Multitech RF760 Manual de usuario
(16 paginas)
(16 paginas)
Redes Multitech MTCBA-G-F2 Manual de usuario
(78 paginas)
(78 paginas)
Redes Multitech MTCBA-C Guía de usuario
(58 paginas)
(58 paginas)
Redes Multitech FR2201 Guía de usuario
(85 paginas)
(85 paginas)
Redes Multitech FF200 Guía de usuario
(68 paginas)
(68 paginas)
Redes Multitech MT1932ZDXI Guía de usuario
(177 paginas)
(177 paginas)
Redes Multitech FaxFinder FF840 Guía de usuario
(35 paginas)
(35 paginas)
Redes Multitech GFU19 Guía de usuario
(30 paginas)
(30 paginas)
Redes Multitech MTR-C2 Manual de usuario
(10 paginas)
(10 paginas)
Redes Multitech MTMC8-USB Guía de usuario
(28 paginas)
(28 paginas)
Redes Multitech ISIHI-2U Manual de usuario
(60 paginas)
(60 paginas)
Redes Multitech RF760 Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales