Multitech MTCMR-E1 Manual de usuario Pagina 86
- Pagina / 119
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 14 – AT Commands
86 Universal IP AT Commands Reference Guide
#CONNECTIONSTART – Start Communication
Description: This command directs the TCP/IP stack to originate an outgoing call.
Upon receiving this command, the TCP/IP stack attempts to complete a connection session.
The TCP/IP stack will dial the number according to the #GPRSMODE value and Dial Option
parameter (DIALN1 or DIALN2 depending on DIALSELECT). If an error occurs, the TCP/IP stack
automatically re-attempts the call origination attempt, according to the REDIALCOUNT
parameter. Once the physical layer is up, the TCP/IP stack runs.
Syntax: AT#CONNECTIONSTART
Command
Possible Responses
AT#CONNECTIONSTART
(Request connection to
network.
This is for GPRSMODE=0.)
DIALING
Note: Phone line is available
2124560123
Note: Dial DIALN1 or DIALN2 number depending on DIALSELECT
CONNECT 9600
Note: Modem speed negotiated between both sides. If the TCP/IP
stack is configured for modem only operation (PPPMODE
parameter), there are no more return codes
213.192.200.4
Note: IP address attributed to the TCP/IP stack
Ok_Info_PPP
Note: As soon as the TCP/IP stack software displays this message, it
is ready to receive commands
AT#CONNECTIONSTART
(Request connection to
network. This is for
GPRSMODE=1 or
GPRSMODE=2)
Ok_Info_GprsActivation
Note: As soon as the TCP/IP stack software displays this message, it
is ready to receive commands
213.192.200.4
Note: IP address attributed to the TCP/IP stack
AT#CONNECTIONSTART
BUSY
Note: A busy signal is detected on the remote site
TCP/IP stack will wait REDIALDELAY seconds then dial again. The
redialing will continue until success or until the number of call
retries defined in parameter REDIALCOUNT has been reached.
AT#CONNECTIONSTART
NO CARRIER
Note: A physical connection could not be completed. The
TCP/IP stack will wait REDIALDELAY seconds then dial again. The
redialing will continue until success or until the number of call
retries defined in parameter REDIALCOUNT has been reached.
Values: Read Parameters:
DIALN1
DIALN2
DIALSELECT
ISPPW
ISPUN
REDIALCOUNT
REDIALDELAY
- Universal IP 1
- Contacting Multi-Tech 2
- Contents 3
- Part 1 – AT Commands 10
- Set Commands 11
- &D – DTR Option 12
- &S – DSR ON or OFF 12
- <parity> 13
- +IFC – Set Flow Control 14
- +IPR – Set Serial Speed 14
- Display Commands 16
- Syntax: AT#VALL 18
- Responses – MT100SEM-IP only 18
- #RECiADD – Set Email Address 21
- #SMTPPW – Set SMTP Password 23
- #SMTPUN – Set SMTP User Name 23
- #POP3UN – Set POP3 User Name 28
- Display Command 29
- #FTPUN – Set FTP User Name 31
- #FTPPW – Set FTP Password 31
- Chapter 4 – FTP AT Commands 32
- #TCPTXDELAY – Time Delay 36
- Chapter 5 – TCP AT Commands 38
- Chapter 6 – UDP AT Commands 46
- #UDPPORT – UDP Port Number 47
- #UDPDLEMODE – Set DLE Mode 48
- Part 2 – AT Commands for the 53
- Part 3 – AT Commands 60
- Chapter 10 – IP AT Commands 62
- #WLANSSID – SSID of WLAN 70
- Chapter 13–WLAN AT Commands 72
- #WLAN? – WLAN Module 77
- Part 4 – 78
- Chapter 14 – AT Commands 80
- #ISPPW – Set ISP Password 84
- #ISPUN – Set ISP User Name 85
- Part 5 – GPIO AT Commands 91
- About GPIO 92
- Part 6 – AT Commands 95
- #GPSPORT – Set GPS Host Port 96
- - Disable 99
- (Disabled) 99
- GPS Message Syntax 100
- GPS Message Examples 101
- GPS Configuration Examples 101
- Introduction 102
- NMEA Protocol Overview 102
- SUPPORTED MESSAGE LIST 102
- NMEA MESSAGES 103
- GLL – Latitude/Longitude 104
- Part 7 – Appendixes 107
- Response Messages 108
- Error Codes 109
- Commands 110
- Responses 110
- TCP Socket Response Messages 112
- Act as a TCP Client: AT#OTCP 113
Relacionado con productos y manuales para Redes Multitech MTCMR-E1
Redes Multitech MTCMR-G2 Guía de usuario
(56 paginas)
(56 paginas)
Redes Multitech MT2834ZPX Guía de usuario
(15 paginas)
(15 paginas)
Redes Multitech MT56DSU2 El manual del propietario
(39 paginas)
(39 paginas)
Redes Multitech MTCBA-C Guía de usuario
(16 paginas)
(16 paginas)
Redes Multitech RF760 Manual de usuario
(16 paginas)
(16 paginas)
Redes Multitech MTCBA-G-F2 Manual de usuario
(78 paginas)
(78 paginas)
Redes Multitech MTCBA-C Guía de usuario
(58 paginas)
(58 paginas)
Redes Multitech FR2201 Guía de usuario
(85 paginas)
(85 paginas)
Redes Multitech FF200 Guía de usuario
(68 paginas)
(68 paginas)
Redes Multitech MT1932ZDXI Guía de usuario
(177 paginas)
(177 paginas)
Redes Multitech FaxFinder FF840 Guía de usuario
(35 paginas)
(35 paginas)
Redes Multitech GFU19 Guía de usuario
(30 paginas)
(30 paginas)
Redes Multitech MTR-C2 Manual de usuario
(10 paginas)
(10 paginas)
Redes Multitech MTMC8-USB Guía de usuario
(28 paginas)
(28 paginas)
Redes Multitech ISIHI-2U Manual de usuario
(60 paginas)
(60 paginas)
Redes Multitech RF760 Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales