Multitech MTCMR-E1 Manual de usuario Pagina 84
- Pagina / 119
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 14 – AT Commands
84 Universal IP AT Commands Reference Guide
#RINGCOUNT – Set Number of Rings/Automatic Operation
Description: This parameter defines the number of rings that will be counted before an automatic operation
occurs when receiving an incoming call.
It applies only when the ANSWERMODE parameter is set to an automatic mode (value>0).
If the ANSWERMODE parameter is used, the RINGCOUNT value must also be >0.
Syntax: AT#RINGCOUNT=<value>
AT#RINGCOUNT? Read or display the current setting (or AT#VPHY, AT#VALL).
Values: Integer between 0 and 15 inclusive.
0 = modem will not answer.
1-15 = modem will answer on the ring number selected.
Default: 0
#DIALN1 – Set Primary Dial-Up Number
Description: This parameter is the primary dial-up phone number that will connect with the local ISP. Length
depends on country/region.
Syntax: AT#DIALN1="<value>"
AT#DIALN1? Read or display the current setting (or AT#VPHY, AT#VALL).
Values: Decimal phone numbers.
Default: No default.
#DIALN2 – Set Secondary Dial-Up Number
Description: This parameter is the secondary dial-up phone number that will connect with the local ISP.
Length depends on country.
Syntax: AT#DIALN2="<value>"
AT#DIALN2? Read or display the current setting (or AT#VPHY, AT#VALL).
Values: Decimal phone numbers.
Default: No default.
#DIALSELECT – Set Internet Connection Number
Description: The value of this command determines the number called to establish an Internet connection. It
configures the TCP/IP stack software to use the primary dial-up number or the secondary dial-up
number.
Syntax: AT#DIALSELECT=<value>
AT#DIALSELECT? Read or display the current setting (or AT#VPHY, AT#VALL).
Values: 1 – Use primary dial-up number.
2 – Use secondary dial-up number
Default: 1
#ISPPW – Set ISP Password
Description: This parameter sets the password for the ISP account. When communication is initiated and
once the physical (modem) connection has been established with the ISP, the TCP/IP stack
software must provide the ISP with the password associated with the account to be used.
Syntax: AT#ISPPW="<value>"
AT#ISPPW? Read or display the current setting (or AT#VPPP, AT#VALL).
Values: Alpha-numeric ASCII text string up to 64 characters.
Default: No default.
- Universal IP 1
- Contacting Multi-Tech 2
- Contents 3
- Part 1 – AT Commands 10
- Set Commands 11
- &D – DTR Option 12
- &S – DSR ON or OFF 12
- <parity> 13
- +IFC – Set Flow Control 14
- +IPR – Set Serial Speed 14
- Display Commands 16
- Syntax: AT#VALL 18
- Responses – MT100SEM-IP only 18
- #RECiADD – Set Email Address 21
- #SMTPPW – Set SMTP Password 23
- #SMTPUN – Set SMTP User Name 23
- #POP3UN – Set POP3 User Name 28
- Display Command 29
- #FTPUN – Set FTP User Name 31
- #FTPPW – Set FTP Password 31
- Chapter 4 – FTP AT Commands 32
- #TCPTXDELAY – Time Delay 36
- Chapter 5 – TCP AT Commands 38
- Chapter 6 – UDP AT Commands 46
- #UDPPORT – UDP Port Number 47
- #UDPDLEMODE – Set DLE Mode 48
- Part 2 – AT Commands for the 53
- Part 3 – AT Commands 60
- Chapter 10 – IP AT Commands 62
- #WLANSSID – SSID of WLAN 70
- Chapter 13–WLAN AT Commands 72
- #WLAN? – WLAN Module 77
- Part 4 – 78
- Chapter 14 – AT Commands 80
- #ISPPW – Set ISP Password 84
- #ISPUN – Set ISP User Name 85
- Part 5 – GPIO AT Commands 91
- About GPIO 92
- Part 6 – AT Commands 95
- #GPSPORT – Set GPS Host Port 96
- - Disable 99
- (Disabled) 99
- GPS Message Syntax 100
- GPS Message Examples 101
- GPS Configuration Examples 101
- Introduction 102
- NMEA Protocol Overview 102
- SUPPORTED MESSAGE LIST 102
- NMEA MESSAGES 103
- GLL – Latitude/Longitude 104
- Part 7 – Appendixes 107
- Response Messages 108
- Error Codes 109
- Commands 110
- Responses 110
- TCP Socket Response Messages 112
- Act as a TCP Client: AT#OTCP 113
Relacionado con productos y manuales para Redes Multitech MTCMR-E1
Redes Multitech MTCMR-G2 Guía de usuario
(56 paginas)
(56 paginas)
Redes Multitech MT2834ZPX Guía de usuario
(15 paginas)
(15 paginas)
Redes Multitech MT56DSU2 El manual del propietario
(39 paginas)
(39 paginas)
Redes Multitech MTCBA-C Guía de usuario
(16 paginas)
(16 paginas)
Redes Multitech RF760 Manual de usuario
(16 paginas)
(16 paginas)
Redes Multitech MTCBA-G-F2 Manual de usuario
(78 paginas)
(78 paginas)
Redes Multitech MTCBA-C Guía de usuario
(58 paginas)
(58 paginas)
Redes Multitech FR2201 Guía de usuario
(85 paginas)
(85 paginas)
Redes Multitech FF200 Guía de usuario
(68 paginas)
(68 paginas)
Redes Multitech MT1932ZDXI Guía de usuario
(177 paginas)
(177 paginas)
Redes Multitech FaxFinder FF840 Guía de usuario
(35 paginas)
(35 paginas)
Redes Multitech GFU19 Guía de usuario
(30 paginas)
(30 paginas)
Redes Multitech MTR-C2 Manual de usuario
(10 paginas)
(10 paginas)
Redes Multitech MTMC8-USB Guía de usuario
(28 paginas)
(28 paginas)
Redes Multitech ISIHI-2U Manual de usuario
(60 paginas)
(60 paginas)
Redes Multitech RF760 Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales