Multitech MultiConnect Adapter Guía de usuario Pagina 140
- Pagina / 154
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 13 – SNTP Client
Command Line Interface and Application Examples for Multi-Tech Systems, Inc. IP Modules (S000368F) 140
Chapter 13 – SNTP Client
Introduction
SNTP Client is used to synchronize timekeeping among a set of distributed time servers and clients. It is built on the
IP and UDP, which provide a connectionless transport mechanism.
Features
• Supports SNTP client built on UDP (port 123) to update the local time after booting and at periodic
intervals.
• Supports to set Standard Name of Time Zone.
• Supports to set offset from UTC.
• Supports Daylight savings feature.
• Supports the configuration of Offset During Daylight Savings, Start of Daylight Savings Time, and End of
Daylight Savings Time.
Command to Enable/Disable SNTP Client
The host/serial device can the use the command below to enable/disable the SNTP client.
# set sntp-client <enable/disable>
Prerequisites
Mandatory Prerequisites: The following details are mandatory configuration and have to be validated before
starting SNTP client:
• Set NTP server name or IP address.
# set sntp-client ntp-server-name <ipaddress>
• Set the time-zone (Default is UTC).
# set sntp-client time-zone <UTC>
• Set the time zone offset to be added
# set sntp-client time-zone-offset <+00:00>
• Set the polling time.
# set sntp-client polling-time <300>
ERROR Message
The set sntp-client command prompts for the ERROR message if any of the above details are not configured or
not valid.
Optional Prerequisites: The following configurations are optional and can be used when you want the host
device to enable daylight savings mode.
• Enable Daylight Savings Mode.
# set sntp-client daylight-saving <enable>
• Set the Daylight Savings Offset value.
# set sntp-client daylight-saving offset <+60>
• Set the Start Ordinal/week for Daylight Savings.
# set sntp-client daylight-saving start-ordinal <First>
• Set the Start Weekday for Daylight Savings.
# set sntp-client daylight-saving start-weekday <sunday>
• Set the Start Month for Daylight Savings.
# set sntp-client daylight-saving start-month <april>
• Set the Start Time for Daylight Savings.
# set sntp-client daylight-saving start-time <10:00>
• Set the End Ordinal/ week for Daylight Savings.
# set sntp-client daylight-saving end-ordinal <Last
• Set the End Weekday for Daylight Savings
# set sntp-client daylight-saving end-weekday <sunday>
• Set the End Month for Daylight Savings.
# set sntp-client daylight-saving end-month <october>
• Set the End Time for Daylight Savings.
# set sntp-client daylight-saving end-time <10:00>
- Multi-Tech IP Connectivity 1
- Revision History 3
- Table of Contents 4
- Chapter 1 – Managing and 7
- Configuring IP Modules 7
- Chapter 2 – IP Command Line 8
- Interface (CLI) 8
- General Setup Commands 9
- • Hardware information 14
- • System Uptime 14
- • Memory Utilization 14
- • Flash Memory Map 14
- IP Setup Commands 15
- Serial Setup Commands 20
- PPP Setup Commands 37
- HTTP Server Commands 44
- SMTP Client – Commands 46
- POP3 Client Commands 49
- FTP Client Commands 52
- SNTP Client – Commands 54
- 2. Too few arguments 55
- Commands 61
- Region Codes Using the CLI 64
- Chapter 4 – Scenario Setup 65
- IP Modes of Operation 66
- Connectivity Using Dialout 68
- Scenario 1 – Manual Dialout 71
- Scenario 2 – Auto Dialout 72
- Dialout Serial s1 74
- Functionality 75
- Telnet Dial-in Features 76
- UDP Dial-in Features 76
- Commands for Auto-Dialin 77
- Serial Tunneling 81
- Auto-Dial-in Using UDP 84
- NMEA Filtering 85
- Network Processor 90
- PPP Configuration 92
- Wakeup-on Call Feature 94
- Show Commands 94
- Connect Type 95
- Chapter 9 – HTTP Server 96
- Setup and Configuration 97
- Configuration Modes 98
- Host Configuration Mode 98
- 2. The Embedded HTML Page 100
- 3. CGI Scripts 100
- Technical Information 102
- Chapter 10 – SMTP Client 103
- Command Prompt 104
- Interactive Mode 105
- Chapter 11 – POP3 Client 112
- Error Messages 117
- Email with Attachment 118
- Chapter 12 – FTP Client 119
- Prerequisites 120
- About Read and Store 139
- Chapter 13 – SNTP Client 140
- Introduction 142
- Module Acting as Client 146
- Module Acting as Server 147
- .....55 153
- ..................55 154
- ..........................54 154
Relacionado con productos y manuales para Redes Multitech MultiConnect Adapter
Redes Multitech MT5656SMI Guía de usuario
(107 paginas)
(107 paginas)
Redes Multitech GFU19 Manual de usuario
(226 paginas)
(226 paginas)
Redes Multitech MTCMR-H Guía de usuario
(27 paginas)
(27 paginas)
Redes Multitech MT2834ZDXI Manual de usuario
(36 paginas)
(36 paginas)
Redes Multitech FF110 Guía de usuario
(167 paginas)
(167 paginas)
Redes Multitech MT128STZLX Manual de usuario
(17 paginas)
(17 paginas)
Redes Multitech FaxFinder FF840 Especificaciones
(99 paginas)
(99 paginas)
Redes Multitech RF760 Manual de usuario
(39 paginas)
(39 paginas)
Redes Multitech MMH900 Guía de usuario
(200 paginas)
(200 paginas)
Redes Multitech RouteFinder MTASR3 Manual de usuario
(33 paginas)
(33 paginas)
Redes Multitech MVP200 Guía de usuario
(44 paginas)
(44 paginas)
Redes Multitech MA30120 Guía de usuario
(29 paginas)
(29 paginas)
Redes Multitech MTCMR-G2 Guía de usuario
(29 paginas)
(29 paginas)
Redes Multitech FaxFinder FF840 Manual de usuario
(24 paginas)
(24 paginas)
Redes Multitech MTPSR1-202ST Guía de usuario
(104 paginas)
(104 paginas)
Redes Multitech MT5634ZBAV.90 Manual de usuario
(13 paginas)
(13 paginas)
Redes Multitech MultiVOIP 100 MVP120 Guía de usuario
(89 paginas)
(89 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales