Multitech MultiConnect Adapter Guía de usuario Pagina 21
- Pagina / 154
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2 – Command Line Interface (CLI)
Command Line Interface and Application Examples for Multi-Tech Systems, Inc. IP Modules (S000368F) 21
Serial Commands – Setup
Command Syntax linkup [serial interface]
Valid serial interface – Modem port s1
Description
Establishes a physical link and PPP on the modem port.
This command is relevant only when the serial interface is a dialing end with
dialing-trig-mode configured as command.
Default Value
-
Success
If physical link is established
OK
Error
The message returned is “ERROR”
Reasons for the Error message are:
1. Too few arguments
2. Dialing-trig-mode is not "command”
3. Link is not established (if PPP fails to get logical link up)
4. Link is already up (when link is established, this command will not tear down and
bring up the link
5. When there is no carrier, no dialtone, or no answer
Command Syntax set serial [s0] auto-dialin <enable/disable>
Description
Enables/disables the device port to Internet connectivity for the serial port s0. This
command is valid only for device port s0
Default Value
Disabled
Success
OK
Error 1. Too few arguments
“Usage: set serial s0 auto-dialin <enable/disable>
Type ‘set serial s0 auto-dialin ? for more information”
2. Multiple matches
auto-dialin auto-dialout
auto-dialin-host auto-dialout-port
auto-dialin-port auto-dialout-protocol
auto-dialin-protocol
3. Invalid string
“error: Invalid string
Type ‘set serial s0 auto-dial-in ? for more information”
4. If “set serial s1 auto-dialin <enable/disable>” is given
“error: Command not supported on the modem port s1”
Command Syntax set serial [s0] auto-dialin-host <hostname/ip-address>
Description
Specifies the auto dial-in host name or IP address.
Note: When a connection is established from serial, a session is established to the
host or IP address mentioned above. This command is valid only for device port s0.
Default Value
NULL
Success
OK
Error 1. Too few arguments
“Usage: set serial s0 auto-dialin-host <hostname/ip-address>
Type ‘set serial s0 auto-dialin-host ? for more information”
2. Multiple matches
auto-dialin auto-dialout
auto-dialin-host auto-dialout-port
auto-dialin-port auto-dialout-protocol
auto-dialin-protocol
3. If “set serial s1 auto-dialin-host 192.168.2.2” is given
“error: Command not supported on the modem port s1”
- Multi-Tech IP Connectivity 1
- Revision History 3
- Table of Contents 4
- Chapter 1 – Managing and 7
- Configuring IP Modules 7
- Chapter 2 – IP Command Line 8
- Interface (CLI) 8
- General Setup Commands 9
- • Hardware information 14
- • System Uptime 14
- • Memory Utilization 14
- • Flash Memory Map 14
- IP Setup Commands 15
- Serial Setup Commands 20
- PPP Setup Commands 37
- HTTP Server Commands 44
- SMTP Client – Commands 46
- POP3 Client Commands 49
- FTP Client Commands 52
- SNTP Client – Commands 54
- 2. Too few arguments 55
- Commands 61
- Region Codes Using the CLI 64
- Chapter 4 – Scenario Setup 65
- IP Modes of Operation 66
- Connectivity Using Dialout 68
- Scenario 1 – Manual Dialout 71
- Scenario 2 – Auto Dialout 72
- Dialout Serial s1 74
- Functionality 75
- Telnet Dial-in Features 76
- UDP Dial-in Features 76
- Commands for Auto-Dialin 77
- Serial Tunneling 81
- Auto-Dial-in Using UDP 84
- NMEA Filtering 85
- Network Processor 90
- PPP Configuration 92
- Wakeup-on Call Feature 94
- Show Commands 94
- Connect Type 95
- Chapter 9 – HTTP Server 96
- Setup and Configuration 97
- Configuration Modes 98
- Host Configuration Mode 98
- 2. The Embedded HTML Page 100
- 3. CGI Scripts 100
- Technical Information 102
- Chapter 10 – SMTP Client 103
- Command Prompt 104
- Interactive Mode 105
- Chapter 11 – POP3 Client 112
- Error Messages 117
- Email with Attachment 118
- Chapter 12 – FTP Client 119
- Prerequisites 120
- About Read and Store 139
- Chapter 13 – SNTP Client 140
- Introduction 142
- Module Acting as Client 146
- Module Acting as Server 147
- .....55 153
- ..................55 154
- ..........................54 154
Relacionado con productos y manuales para Redes Multitech MultiConnect Adapter
Redes Multitech MT5656SMI Guía de usuario
(107 paginas)
(107 paginas)
Redes Multitech GFU19 Manual de usuario
(226 paginas)
(226 paginas)
Redes Multitech MTCMR-H Guía de usuario
(27 paginas)
(27 paginas)
Redes Multitech MT2834ZDXI Manual de usuario
(36 paginas)
(36 paginas)
Redes Multitech FF110 Guía de usuario
(167 paginas)
(167 paginas)
Redes Multitech MT128STZLX Manual de usuario
(17 paginas)
(17 paginas)
Redes Multitech FaxFinder FF840 Especificaciones
(99 paginas)
(99 paginas)
Redes Multitech RF760 Manual de usuario
(39 paginas)
(39 paginas)
Redes Multitech MMH900 Guía de usuario
(200 paginas)
(200 paginas)
Redes Multitech RouteFinder MTASR3 Manual de usuario
(33 paginas)
(33 paginas)
Redes Multitech MVP200 Guía de usuario
(44 paginas)
(44 paginas)
Redes Multitech MA30120 Guía de usuario
(29 paginas)
(29 paginas)
Redes Multitech MTCMR-G2 Guía de usuario
(29 paginas)
(29 paginas)
Redes Multitech FaxFinder FF840 Manual de usuario
(24 paginas)
(24 paginas)
Redes Multitech MTPSR1-202ST Guía de usuario
(104 paginas)
(104 paginas)
Redes Multitech MT5634ZBAV.90 Manual de usuario
(13 paginas)
(13 paginas)
Redes Multitech MultiVOIP 100 MVP120 Guía de usuario
(89 paginas)
(89 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales