Multitech MultiConnect Adapter Guía de usuario Pagina 81
- Pagina / 154
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 6 – Serial-to-Network Connectivity Using Serial Dial-in
Command Line Interface and Application Examples for Multi-Tech Systems, Inc. IP Modules (S000368F) 81
Scenario 4 – Serial Tunneling Mode
The scenario shows how to setup serial-to-serial tunneling using two MTS2SA (Serial-to-Serial) adapters/device
servers, two external modems, and two phone lines. Assume both MTS2SAs are using factory default settings.
Serial Tunneling
Setup Serial Tunneling Feature
Setup MTS2SA Adapter/Device Server #1
Setup as Auto-Dialout (Wait & Answer Call)
Setup MTS2SA Adapter/Device Server #2
Setup as Auto-Dialout (Dialing & Making the
Call to MTS2SA #1)
# set ip telnet auto-dialout enable
# set serial auto-telnet enable
# set ip telnet raw enable
# set serial s0 raw-dialin enable
# set serial s0 raw-dialout enable
# set serial s1 connect-type modem
# set ppp ppp0 ipcp-mode client-or-lan
# set ppp ppp0 dialing-max-retries 3
# set ppp ppp0 dialing-retry-interval 10
# set ppp ppp0 idle-timeout 0
# set ppp ppp0 authentication enable
# set ppp ppp0 auth-type pap-chap
# set ppp ppp0 username test
# set ppp ppp0 password test
# set ppp ppp0 local-ip-addr 202.1.1.2 mask
255.255.255.0
# set ppp ppp0 remote-ip-addr 202.1.1.1 mask
255.255.255.0
# set serial s1 modem dialing-trig-mode command
# set login auto-dialout disable
# save
# set serial auto-telnet enable
# set ip telnet raw enable
# set serial s0 raw-dialin enable
# set serial s0 raw-dialout enable
# set serial s0 auto-dialin trig-mode dtr-char
# set serial s0 auto-dialin-ipadd 202.1.1.2
# set serial s0 auto-dialin-port 5000
# set serial s1 connect-type modem
# set serial s1 modem dial-number 5965
# set serial s1 modem hangup ""
# set ppp ppp0 ipcp-mode client-or-lan
# set ppp ppp0 dialing-max-retries 3
# set ppp ppp0 dialing-retry-interval 10
# set ppp ppp0 idle-timeout 0
# set ppp ppp0 authentication enable
# set ppp ppp0 auth-type pap-chap
# set ppp ppp0 username test
# set ppp ppp0 password test
# set ppp ppp0 local-ip-addr 202.1.1.1 mask
255.255.255.0
# set ppp ppp0 remote-ip-addr 202.1.1.2 mask
255.255.255.0
# set serial s1 modem dialing-trig-mode none
# set serial s0 auto-dialin enable
# save
You will have to change the dial number "set serial s1 modem dial-number 5965" to match up with the phone line that
is connected to adapter #1
In order to terminate the auto-dialin setup in Adapter #2, perform the following:
1. Make sure your firmware version is 1.08 or above. If you have 1.07 or below, you will have to reflash the
firwmare.
2. Power off and on. Then when you see the Ready message, you have 3 seconds to press Control+C. A login
prompt displays. If you do not see the login prompt, repeat this step.
- Multi-Tech IP Connectivity 1
- Revision History 3
- Table of Contents 4
- Chapter 1 – Managing and 7
- Configuring IP Modules 7
- Chapter 2 – IP Command Line 8
- Interface (CLI) 8
- General Setup Commands 9
- • Hardware information 14
- • System Uptime 14
- • Memory Utilization 14
- • Flash Memory Map 14
- IP Setup Commands 15
- Serial Setup Commands 20
- PPP Setup Commands 37
- HTTP Server Commands 44
- SMTP Client – Commands 46
- POP3 Client Commands 49
- FTP Client Commands 52
- SNTP Client – Commands 54
- 2. Too few arguments 55
- Commands 61
- Region Codes Using the CLI 64
- Chapter 4 – Scenario Setup 65
- IP Modes of Operation 66
- Connectivity Using Dialout 68
- Scenario 1 – Manual Dialout 71
- Scenario 2 – Auto Dialout 72
- Dialout Serial s1 74
- Functionality 75
- Telnet Dial-in Features 76
- UDP Dial-in Features 76
- Commands for Auto-Dialin 77
- Serial Tunneling 81
- Auto-Dial-in Using UDP 84
- NMEA Filtering 85
- Network Processor 90
- PPP Configuration 92
- Wakeup-on Call Feature 94
- Show Commands 94
- Connect Type 95
- Chapter 9 – HTTP Server 96
- Setup and Configuration 97
- Configuration Modes 98
- Host Configuration Mode 98
- 2. The Embedded HTML Page 100
- 3. CGI Scripts 100
- Technical Information 102
- Chapter 10 – SMTP Client 103
- Command Prompt 104
- Interactive Mode 105
- Chapter 11 – POP3 Client 112
- Error Messages 117
- Email with Attachment 118
- Chapter 12 – FTP Client 119
- Prerequisites 120
- About Read and Store 139
- Chapter 13 – SNTP Client 140
- Introduction 142
- Module Acting as Client 146
- Module Acting as Server 147
- .....55 153
- ..................55 154
- ..........................54 154
Relacionado con productos y manuales para Redes Multitech MultiConnect Adapter
Redes Multitech MT5656SMI Guía de usuario
(107 paginas)
(107 paginas)
Redes Multitech GFU19 Manual de usuario
(226 paginas)
(226 paginas)
Redes Multitech MTCMR-H Guía de usuario
(27 paginas)
(27 paginas)
Redes Multitech MT2834ZDXI Manual de usuario
(36 paginas)
(36 paginas)
Redes Multitech FF110 Guía de usuario
(167 paginas)
(167 paginas)
Redes Multitech MT128STZLX Manual de usuario
(17 paginas)
(17 paginas)
Redes Multitech FaxFinder FF840 Especificaciones
(99 paginas)
(99 paginas)
Redes Multitech RF760 Manual de usuario
(39 paginas)
(39 paginas)
Redes Multitech MMH900 Guía de usuario
(200 paginas)
(200 paginas)
Redes Multitech RouteFinder MTASR3 Manual de usuario
(33 paginas)
(33 paginas)
Redes Multitech MVP200 Guía de usuario
(44 paginas)
(44 paginas)
Redes Multitech MA30120 Guía de usuario
(29 paginas)
(29 paginas)
Redes Multitech MTCMR-G2 Guía de usuario
(29 paginas)
(29 paginas)
Redes Multitech FaxFinder FF840 Manual de usuario
(24 paginas)
(24 paginas)
Redes Multitech MTPSR1-202ST Guía de usuario
(104 paginas)
(104 paginas)
Redes Multitech MT5634ZBAV.90 Manual de usuario
(13 paginas)
(13 paginas)
Redes Multitech MultiVOIP 100 MVP120 Guía de usuario
(89 paginas)
(89 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales